Jump to content
SAU Community

Recommended Posts

9 minutes ago, Leroy Peterson said:

Birds chasing dat hot copper efame. Don't lower yourself to their level

I'm a washed up celebrity on there

I created their level

Some seriously interesting stuff on there though. It used to be nothing but speculation and cheering each other on for support during the downturn, with a rare informative post here and there. Now there are some experts on rock mechanics and oil drilling offering up explanations of events. Will be staying tuned.

I'm a washed up celebrity on there
I created their level
Some seriously interesting stuff on there though. It used to be nothing but speculation and cheering each other on for support during the downturn, with a rare informative post here and there. Now there are some experts on rock mechanics and oil drilling offering up explanations of events. Will be staying tuned.

Yeah I read Ya's posts and basically ignore the rest.

No one gives a f**k about some dudes 92 yro dad passing away and a f**king essay about how he's dealing with it. Then 400posts of people sending their condolences. It's an ASX forum, not a Remember The Titans discussion board.
1 minute ago, Leroy Peterson said:


Yeah I read Ya's posts and basically ignore the rest.

No one gives a f**k about some dudes 92 yro dad passing away and a f**king essay about how he's dealing with it. Then 400posts of people sending their condolences. It's an ASX forum, not a Remember The Titans discussion board.

Now I feel like registering just to do that 

1 hour ago, UNR33L said:

Birds told me it was the worst time to sell when I did :P 

Now I can buy back in 2c cheaper :D

Yep, got the call wrong on that, but had 88E not released an announcement that confused the market then prices would still be the same or possibly higher.

Regardless I think it's dangerous not to be in the share at the moment. Whatever you pay for them now will seem insignificant if the flow is proven good.

In piece of shit laptop news, msi rekin it's some shit about this chipset not being compatible with Windows 10, something about Intel not supporting some rapid storage shit... Gave me the recovery process which doesn't work, but apparently I'm following the two steps of power on and press f3 wrong...

Won't boot from the windows 10 usb I made when I updated after getting it back either.. Only idea I can think of is make a windows 8 boot disk and try boot from that and install... Then be stuck with windows 8... Or buy a new laptop..

47 minutes ago, Leroy Peterson said:


Why that?

Every time there's a massive global ransomware attack or another variant of it 

Too expensive to get them though :D

Edited by UNR33L

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...