Jump to content
SAU Community

Recommended Posts

Could do, do not know. I will probably have the motor out by the look of things and will see what can be done at the same time ???

Who is doing the work?

Why the cam change?

Were they dialled in extensively last tune?

Why not just chuck some chemiweld in?

Who is doing the work?

Why the cam change?

Were they dialled in extensively last tune?

Why not just chuck some chemiweld in?

Jez will be doing the work.

Cams were dialled for a more even result, top and bottom

I believe Chemiweld had already been used, but that is only a guess

If I did change the CR . probably go 9:1

But I will not make any decision until it is pulled down and the problem found and go from there once I find out the initial problem :(

If you're happy with everything else then why not just resolve the head gasket issue?

Who said it was a head gasket, hope you are right, I tend to always think the worse and anything less is always a better outcome :)

Not going to say anything until the problem is found and fixed, I will go from there but while the car is in the shop might do a couple of tweaks.

Car goes in 12th of next month :rolleyes:

I will not bore you blokes until I have some results and poke the new Dyno Graph up

  • Like 1
  • 4 weeks later...

hmm I was just thinking about this thread the other day.

cracked block would be a bad outcome, but it doesn't really reflect on any shop involved in the build, its more just bad luck. You were pushing a mile of power through a standard wall block and it's not unheard of.

I am amazed sometimes on this thread.

At first the water lose was on a low boost run in tune and limited to 5000rpm, this was in March this year.

This water situation started from the first day of the build, it was not noticeable at first as I was checking the radiator, cold in the mornings and not the overflow, once the overflow emptied then it was noticeable from the radiator. I have always checked from the radiator so I knew exactly how much water was being used, I used a measuring cup.

The amount used on different driving situations was and is the same from day one as it was when we found the water in the oil.

Yet the oil still looked clean on the stick , not as you would expect ?

Edward lee now crd?

If I am not mistaken they said they tak no responsibility for any issues after Jez touched it. Therefor the only way you will have a chance at getting them to fork up for the new repairs is by taking them to court.

Or am I mistaken

I took them to NCAT, a tribunal were you can negotiate and come to a mutual agreement, I sat at home on the phone during this procedure. he was just a smart arse and told me to fark off, I didn't!

This situation is early days and the motor has to be checked , I am sure it can be worked out, until then it is just another bump in the road.

Some blokes should put themselves in the other persons shoes before posting, think about what you would do in the same situation , roll over like a dog , yeah sure ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah, new members can't post pics until they reach a certain post count. If I get a chance I'll promote you to full member, if @Prank or someone else doesn't get there first.
    • Drilled the rubber out on a slow speed and it didn't catch much at all. Probably only half a dozen holes was enough to shred the rubber and it dropped off easily leaving the inner sleeve behind. Will tackle that later
    • I havent bought a manual cover for the dash yet and no cluster change, won't bother me too much, I just need to get that auto box gone, manual in! I miss my manual. 🤪. We started last weekend and managed to get the box out. Planning to start putting it in this weekend and then order a single piece tail. We were super careful to take time and not damage anything. It's my first time working under the car.  With my S15 mainly worked in the bay. This time, it was a headache because of three or four bolts only. They simply didnt want to leave thei homr and the one securing the tailshaft, another above the GB, and the one securing the lipstick was a shit. Mates mate, Davo caught fire 🤣, nearly opened his chest up with a grinder 🤦🏽‍♂️ and both mates nearly had a plate from the box land and slit their head open. Fun times. We all survived. Not the easiest working with limited access on jackstands. As I'm sure we can agree these are the memories which make us love our car. For all three of us, was an awesome weekend and Sunday 3.30am before tools down was a fantastic effort. I need to upload pics, but looks like it needs to be via Url now. We used to be able to just upload pics back in the day. It's been that long! 🤪 Im currently spraying rustoleum under body, not because it's rusted. It's super clean, but just so it's protected for the next 10 years. There was a few surface rust spots. Which pretty much wiped off with a 3M scourer.  Really impressed with how well the previous owner maintained it. Bank account went down so quick! Service, then GB - managed to get a spanking new 34 genuine box from Nissan. All the rest of the conversion parts from Kudos.  Went with a Nismo short shifter. New pedals and Exedy Clutch and FW. Ordered the Prp Rear Main Retainer kit which should arrive Friday and my first engine mod part just like I did with my S15 will be the Tomei Expreme Turbo Outlet. Already on order. It'll likely sleep next to me on a pillow during the coming months. 🥰 Last build was on my JET200GT profile and on SAU and Hardtuned I had documented the build. Planning to try to do that again. Brands feel scarce now. Wish we still had ARC and Apexi parts readily available. Exhaust - need some advice on this. I had an Apexi exhaust on the S15 and loved the tone. My mate had a HKS HP Silent on his 33 and suggested I go with that to avoid drone. I can't remember hearing an RB25DET running that so will likely need to wait for a meet or something to hear it.  Not after big power, just enjoy building it, and drivability with minimal negative attention.
    • Have a chat with Ben at Moore Performance or Jesse at JS Performance.
    • Thanks both. All good advice. Reminds me of drilling through stone wall for drainage pipe 😬 I'll let you know how I get on if I still have use of my hands afterwards 😅
×
×
  • Create New...