Jump to content
SAU Community

Jason's Skyline R32 Gt-r Build - Tx Usa


Recommended Posts

As I mentioned a few posts back, the car comes with a stack of maintenance records. Looking for some help deciphering some major overhaul work that was done nine years and 40km ago. Looks possible that there was a factory engine and chassis refresh done, as it was done by Nissan Prince Motorsports.

Cross posted from the Japan forum:

http://www.sau.com.au/forums/topic/462125-major-overhaul-records-looking-for-help-w-translation/

Invoices attached for reference.

Chassis Refresh Records BNR32-001502.pdf

Engine Refresh Records BNR32-001502.pdf

Link to comment
Share on other sites

I was able to get the overhaul records translated (fiverr.com - very fast and reasonable).

Turns out I had misread the chassis refresh invoice and it was actually 2MM yen of work - so a total of 2.3MM yen. $20K US at today's rate. Lot of work done on this car 9 years ago.

I attached the translation in a spreadsheet, two tabs. In case anyone is interested.

I was hoping to see where they had addressed the low compression on cylinder 2, but not clear from the translation whether that was done or not. They may have changed a head gasket and it's just a bad translation.

Anyway, we'll do a compression test when it gets here in less than 2 weeks and see what we're in for short term. I'm glad it doesn't seem built at all ... I have some plans over time.

Painted EH7 (fairlady yellow, as I suspected).

OTHER GOODIES ON THE CAR I DISCOVERED IN THE RECORDS STACK:

- Nismo circuit link (tension rods, control arms, etc. - just no performance dampers)

- Nismo sports clutch and flywheel

- Trust exhaust is titanium

All of that was put on in 2006.

Car_Service_Record.xlsx

Link to comment
Share on other sites

I bid on that car!

I almost won it too - bid 13,000 yen less than it sold for.

glad to see it found a good home and those records that had me drooling are the real deal.

Link to comment
Share on other sites

Hey, small world! It took me a while to win a good one. I hope you've been able to snag one by now?

I'm looking forward to getting it here for a full look-see. Paper trail so far is definitely pretty good.

Hope I do it justice!

Link to comment
Share on other sites

Hey, small world! It took me a while to win a good one. I hope you've been able to snag one by now?

I'm looking forward to getting it here for a full look-see. Paper trail so far is definitely pretty good.

Hope I do it justice!

I did, two days later. it's probably sitting next to yours on the Hoegh St. Pete right now!

  • Like 1
Link to comment
Share on other sites

  • 3 weeks later...

It's finally here! I picked the car up at the port in Freeport, TX a few days ago, and drove it 2 hours home.

It's even better than I had hoped. Paint and interior are in great shape (a couple of minor chips). Seems very mechanically sound and pulls hard on boost. A few other goodies which we didn't know about include HIDs and a new battery. It feels like a really great base to build from.

No issues so far. I'm on travel now and will do the compression test and change the fluids when I get back, as well as get it registered. I'll also get the new rims (Omori Factory Spec LMGT4s 18x9J) on and wrapped in the Michelin Pilot Super Sports (255/40/18) that should be there when I arrive back home. It needs a good detailing too.

I'll take more pics inside and out when I return home and do the next update.

12523163 10153760780410801 6050273357998277013 N


image

  • Like 2
Link to comment
Share on other sites

Ac unit might be in the centre console with the wires extended. Mine was as the previous owner must have had a big double din headunit installed then removed it before the sale.

Then again maybe they didnt want a working heater or ac haha

Shaping up to be a great build already!!!

k_d you're absolutely right it was in the console. Pulled the trigger too soon.

Link to comment
Share on other sites

Had the Nismo Omori rims (18x9J) installed today with Michelin Pilot Super Sports (255/40/18).

As you can see in the wheel pic, could stand some serious lowering, especially in front. It was put high for its trip on the boat. Will try to get to that tomorrow.

Also gave her a wash and dry + was able to get off all of the paint / shoe polish used to mark the window during export. Never seen a car this dirty. I've also never used that much acetone in one sitting. And LOTS of "elbow grease".

post-141992-0-55116700-1454290044_thumb.jpg

post-141992-0-71226700-1454290039_thumb.jpg

post-141992-0-95024600-1454290046_thumb.jpg

Link to comment
Share on other sites

New Nismo bits arrived from Yahoo Auctions Japan.

Installed new retro Nismo logo shift knob + CF mirror cover. S-tune meters + Nismo horn to be installed later. Also received (but not pictured), intercooler piping for the Nismo IC received a few weeks ago. It needs a good refresh and won't be installed for a while.

Also in the background is my red Nismo kill switch lighter, installed last week. I'm not going full Nismo on this, but pretty close.

Also installed a new panel filter & degreased the airbox, which was full of 150,000 KM worth of gunk. It was pretty nasty. Response is definitely different now.

post-141992-0-54283200-1454359835_thumb.jpg

post-141992-0-31616600-1454359839_thumb.jpg

post-141992-0-37302000-1454359844_thumb.jpg

  • Like 1
Link to comment
Share on other sites

A couple of washes later the car is fully registered now. Car has been lowered substantially (if you can tell). It could still use further lowering in front, I think. Ohlins DFV coilovers and TBD (but really stiff) springs for suspension. Front will go all the way down now. Rear may go down a little more. Trying to avoid rubbing on these bumpy Texas roads.

New headunit installed (playing late '80's US R&B, if course) and my two older kids (14 and 12) helped me show her off at the local "coffee and cars" meet-up this morning. With only five or six R32 Skylines in the Houston area (third largest US city), they are a very rare sight and obviously this yellow is incredibly unique. Had a lot of lookers and picture-takers.

More substantial mechanical work coming this week. fluids and filters.

post-141992-0-17556800-1454897386_thumb.jpg

post-141992-0-90042800-1454897390_thumb.jpg

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • It's generally best practise to run 1x run without VCT enabled, then 1x run enabled till redline. Overlay the two torque graphs and you'll find the desired RPM to turn off VCT. Sometimes, it might be even worthwhile turning off VCT earlier control torque/cylinder pressure and using VCT purely to spool the turbo.
    • They sell them in Malaysia for about $4
    • First time I ever have issues with Amazon, but my wife often tells me to keep an eye out for fakes. It finally got me. I wrapped up the conversation with Gates. The gentlemen I was talking to seemed to hate his job but the response time on their technical support is outstanding. He stated that the hose is marked with some variation of "SAE J30R10" but that if you only purchase a 1 foot length like I did, it is possible to get a cut between markings and have a blank hose. To no ones surprise, he stated the swelling and "gummyness" isn't normal and to replace/buy from somewhere else (He mentioned NAPA). I'll toss a small end of the new one in gas for a few days before pulling the hanger out again, just to be safe.  Hose should arrive Monday. For those running multiple pump in tank hangers, you know the joys of getting them out and back in. I'm surprised I haven't destroyed my level float yet.  Lastly once I wrap all of this up, I'm planning on hitting the dyno again in 2 weeks while I'm on vacation. I realized recently that my VCT is set to turn off at 5000RPM. I'm surprised it wasn't increased while I was on the dyno last. I'm expecting I can increase it to ~6500RPM, if not more. Should hopefully get another 15-20kw out of it. I also want him to revisit my knock thresholds. I'm occasionally getting false knock around 3000rpm. 
    • All jokes aside, OP they're just called R32 oem rims as you said. The Nissan engineers back in the late 80's loosely copied the design from the Koya Driftek which was designed and produced about 18 years later.
×
×
  • Create New...