Jump to content
SAU Community

Recommended Posts

Rb20det compression test. A tad off operating temp. Results from camcover to firewall. 140ps.140ps.130ps.135ps.135ps142ps. Is that a bad reading ? Motor has done 140ks. Reason for testing is it has recently started to smoke badly .whiteish smoke

Link to comment
https://www.sau.com.au/forums/topic/461872-rb20det-compression-test/
Share on other sites

Rb20det compression test. A tad off operating temp. Results from camcover to firewall. 140ps.140ps.130ps.135ps.135ps142ps. Is that a bad reading ? Motor has done 140ks. Reason for testing is it has recently started to smoke badly .whiteish smoke

Has the engine had new oil put in? If so what brand and weight? Maybe check your oil pressure and turbo seals, is it constant smoke if the plugs are fouling up would be a sign of combustion chamber oil you could eliminate the source of the oil burning up by possibly checking plugs.

140K shouldnt be too bad on the rings though depending on how hard the vehicle has been driven. If it is rear turbo seal then it wouldnt be combustion chamber and you should see signs of oil leak on the rear of the turbo. Oil pressure to the turbo cant exceed otherwise it can pass the seal.

Have you done anything to the engine or did it just start to slowly get more smoke? Or did it just start smoking bad all of a sudden? Has the vehicle overheated could even be a head gasket between the oil journals or returns. If this was the case you would be seeing more blow by as the number 3 appears to be 10 to 12 below the highest reading.

Could even be valve stem seals or depending on the smoke color if it is white then it seems more like moisture/water blueish is oil being burnt.

Maybe post up some more findings and can help narrow it down.

Is it constant cold start or when it gets more to operating temp?

Hope this helps

did a comp test on a genuine 90K stock motor rb20det just recently, 160-165 PSI across the lot, no smoke at idle but has a puff when you first come on boost but clears an does not return unless you get caught in traffic.

For that engine Missleman I'd suggest valve stem seals are in need of replacement.

They get hard as wood and eventually disintegrate.

Having said that, I'm a firm believer that unless you're totally in love with your 20, any engine overhaul is money wasted. Better to drop in something newer.

Do the sums just for a full gasket set and you're halfway towards a newer/bigger capacity donk.

  • Like 1

Grey or Blue Smoke = Engine Oil Burning

Valve Stem Seals - Turbo Seals - PCV Blocked - Valve Stem Guides - Piston Rings

Compression or Leak Wet Test - Compression can also be down from Leaking Valve or Piston Rings - Cam Lobe rounded not allowing valve to open the same as others hence lower comp reading. Checking these with comp test and wet test or leak test will determine which parts are allowing comp leak

White Smoke = White smoke (Steam) or water/coolant/antifreeze vapor from the exhaust. normally when water vapor heats up it dissipates and not as noticeable if the vapor stays then there is an issue - for Auto vehicles sometimes the trans fluid can enter the intake on some vehicles through the modulator - this also burns at this color and close to grey color

Cracked Head, Cracked Cylinder Block, Head Gasket stuffed between water and cylinder allowing water in and lowering compression - in this case you can see the water movement in the radiator going up and down most times.

When your vehicle is running check the radiator water movement - if it goes up and down then head gasket between cylinder and water jackets

Check your oil cap for coolant/water/antifreeze what ever you want to call it for signs of milky chocolate looking contaminents on the oil cap or dipstick

If its water to oil on the head gasket then obviously the oil cap will be full of milky sludge and eventually the worse it gets you would notice this pretty quickly

Black Smoke = Fuel too rich - can be caused from many things just to list a few, injector issue, blocked air cleaner, sensor issue, ignition problem, FPR stuck,

Obviously any smoke coming from your exhaust is a sign of something not quite right

Edited by tuning_vs_hardware

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...