Jump to content
SAU Community

Recommended Posts

Yes that rasp and the volume does seem to indicate a complete absence of any baffles and sound absorbing materials... The sound is litterally just bouncing around the pipes...

Certainly explains the touchy throttle with no restriction.

When I had the stock turbo, I'd be on boost reversing up driveways.

100 cell cat fitted today as there was none, a tad quieter but not much.

Less rasp. Next to zero loss in performance.

The mufflers looks as new, no evidence of cutting open or modification.

I did a poke inside the rear muffler to feel for baffles and/or walls.

It appears completely hollow.

It's looks the same system as Luis.

The previous owner told me he went for a straight through option on the exhaust.

Anyway, still have AMPerformance intake to stick on, then tune. Probably be louder again.

  • Like 1

Certainly explains the touchy throttle with no restriction.

When I had the stock turbo, I'd be on boost reversing up driveways.

100 cell cat fitted today as there was none, a tad quieter but not much.

Less rasp. Next to zero loss in performance.

The mufflers looks as new, no evidence of cutting open or modification.

I did a poke inside the rear muffler to feel for baffles and/or walls.

It appears completely hollow.

It's looks the same system as Luis.

The previous owner told me he went for a straight through option on the exhaust.

Anyway, still have AMPerformance intake to stick on, then tune. Probably be louder again.

Intake will change bugger all.

It's already metal; all you're doing in putting a bigger pipe down to the same inlet restriction.

  • 1 month later...
  • 3 months later...

Is that for the 2.5 and 3.5 litre motors ? My flanges are badly rusting and figure I'll be needing to do something soonish and I've got the 3.5...

All NM35 (VQ25det) cat-back exhausts will fit a PNM35/PM35 (3.5L) without modification.

The M35 (VQ25dd) utilises different hangers for the rear muffler for whatever reason.

  • Like 1
  • 1 month later...

ok sorry revisiting this again.

People are constantly commenting how loud my car is so back to work on it.

My exhaust is Legalis R, twin 83mm tips. Fujitsubo stamp on the rear muffler

Rear muffler is straight through with a perforated inner skin. (Boomer)

I can see the inlet with a torch.

Internal outlets look 50mm then flare to 83mm

Can anyone confirm this is the genuine design for this system ?

Thinking of fitting a chambered rear if it won't be too restrictive..

thanks

 

Are these car people or just general population?  As someone not into cars may think anything louder than a prius is too loud.

It's possible yours may have been modified as I have a freeway dolphin dump and front pipe, into a fujibutso legalis R and it's very quiet a full turbo back 3inch. I also have a 7m powered soarer with 3inch kakimoto exhuast which sets off car alarms it's so loud in comparison.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...