Jump to content
SAU Community

Recommended Posts

hey,

so just had my r33 gts-t tuned for the first time.

these are the mods:

3inch custom turbo back exhaust

HKS GT-RS turbo

Nismo 550cc injectors

yellow jacket coil packs

ngk Bcpr7ES 0.9mm spark

z32 AFM

Nismo fuel pump

Blitz return flow intercooler

Apexi power fc

Apexi pod filter

Drift catch can

Greddy sm integrate gauges (boost, oil temp, oil pressure, water temp, fuel pressure)

Greddy EBC

Car made 237kw at the wheels on 18 psi and just under 200 kw on low boost setting (12 psi)

it was all good on the dyno but on the road using high boost it was misfiring horribly when booting it.

Trent,who tuned the car mentioned that when he took it for a drive that it did misfire but then it went away and wasn't doing it.

maybe its my driving but it was horrible when i took it for a spin.

He said it might need better gapped spark plugs to help the coil packs and mentioned that yellow jackets are known for misfiring, which upsets me since i bought them less then months ago. Car drives great on low boost atleast but thats no fun at all lol

Anyone else have similar experiences with yellow jackets ? could 0.8mm gapped spark plugs make it any better or is it worth begging for a refund for the yellow jackets and going splitfires ?

Does 237kw seem a bit low for 18psi ? what could be causing it to be a bit down on power ? was expecting over 250kws to be honest from what i had seen on the forums

:(

i'll see if my scanner works and post up dyno sheets

I cooked 2 out of the 6 Yellow Jackets I got, replaced them.. then kept misfiring, even with plugs gapped at 0.5mm... so I took them out in lieu of brand new Splitfires.. I now run upwards of 23 psi no misfire :)

Buy either OEM or Splitfire or convert to LS coils or similar.. those colourful coilpacks are all junk (trying to avoid naming names)

Also your lower power reading could be from your poor spark performance

  • Like 1

Ask for a refund and move onto standard or splits. standards are only $50 more than the splits from kuosmotorsport.

OR

What plugs are you currently using? Did you change them when you changed the coilpacks?

thanks for the quick replies :D

plugs that are in now are ngk Bcpr7ES 0.9mm i didnt regap them as i never done it before and it didnt want to stuff it up lol.

They were changed same time as coil packs.

i've emailed the place i bought the coilpacks from and asked for a refund so ill see what happens. ill be pissed if they dont refund me :(

will i need a touch up tune when if i change coilpacks ?

i'll have someone do the sparkies for me since im retarded at doing little things like that. and if that doesnt work i guess i know its 100% the coilpacks.

so you guys recon i could gain a bit more power with splitfires if that might of been the limiting factor. apart from the misfiring the car drives fantastic now after the tune and cold star issues have gone and gained a decent amount of power on the dyno.

can someone tell me why it wouldnt be misfiring while on dyno but misfiring while driven on the road ? first time i had any car tuned so new to all of this :)

I had the same issue at 235rwkw. Gapped the plugs to about .6mm and it's sweet as.

I think you are aware of the problem (being the coils) and band aiding it by gapping the plugs down isn't really going to be a long term solution.

Our setups are quite similar. Same turbo, computer, AFM, injectors. Though my car makes around 40 rwkw more at the same boost.

I run Splitfires and only had an occasional misfire when using BCPR6ES plugs, but since changing to one heat range colder (the same as you are running) I've had no misfire issues.

Edited by Ryno

whoa 40kws more then me, now i'm even more devastated :( lol would the difference in power be due to the bad coils/plugs? big difference !! i was expecting closer to 260 and was pretty disappointed with what i got.

trent recommended NGK bcpr7eix gapped down to 0.55mm so ill give those a go and see if it improves. i wont bother getting a touch up tune till i can get splitfires put in.

Really hope i can get closer to 260rwkws!

Edited by deprived777

Yeah you should make 260... I've got a trick exhaust manifold and run an external waste gate, which gives me an extra 20 kW or so and about 500 rpm better response.

Too many people care about numbers, just get rid of the shit Coilpacks, buy OEM or Splitfires as mentioned by everyone and enjoy the car.

Get someone to gap your plugs down or do it yourself. You can buy a tool from super cheap auto.

If there was no evident misfire issue on the dyno while Trent was tuning, then there will hardly be any power difference after the touch up. There are hundreds of other reasons why it could be down on power but not up for discussion now.

yeah i'll get them regapped and go from there. but if i can be making more power then why not chase it.unless its going to cost a fortune then i'll leave it as it is.:)

may be a number but in my mind 260 and over would make me happy lol

i'll take out the plugs tomorrow and get someone to gap them for me.

If you can remove the coils and take out the plugs you can gap them. Just get some feeler gauges and there is probably a how to on the web if you can figure it out yourself. In fact just tap the plugs gently on a vise or something and keep measuring the gap.

Sounds like you need new coils though.

I did attempt to gap an old spark plug using one of those Rosen medallion type gap tools but it juat wasn't going right for me lol I'll look for a feeler gauge but probably be easier for me to get someone else to do it haha. Yeah I'm thinking coils too from the bad things I'm hearing about them. They sounded promising at the time and I was reading mostly good things but I guess I must of just been looking for the good things being said :/ wish I waited and bought splitfire. I don't know of they'll refund me of not. Fingers crossed!

They're good as paper weights.

I only bought replacement ones because the car already came with them, after replacing 2x coils and still having misfires I just bit the bullet and bought Splitfire coils and haven't looked back.

However if I could have a stab at it again, I would just convert straight to LS coils.

works out about the same, a little more dicking about.. but you'll have spark for days and easily run 0.8mm gap without any misfire at like 20+ psi.

I got a mate who runs them on his SR20 and putting 25psi through the motor and he runs his gap at 0.8mm errday :)

With Splitfires they tend to break down if you run 0.8mm at 20+ psi and with more dwell in them they will run ok till they overheat and start misfiring a little time later.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...