Jump to content
SAU Community

Recommended Posts

dont get me started on YJ's and performance China Racing wise lol. I think a few of you saw the shit storm on some of the products I and a few others had bought which do not fit.

FYP

  • Like 1

FYP

good call. fixed it myself too ;)

I HAVE to say; That certain supplier is worse than the producer, as they should have stopped importing certain parts. Anything to make a quick buck eh? Don't worry about stepping over anyone on your way there.

quick question ,what if you over tap the spark plug and the gaps to small. what do you use to widen the gap without damaging it ?

quick question ,what if you over tap the spark plug and the gaps to small. what do you use to widen the gap without damaging it ?

i have used a flat head in the past and was very careful to push it up.

I think you are aware of the problem (being the coils) and band aiding it by gapping the plugs down isn't really going to be a long term solution.

Our setups are quite similar. Same turbo, computer, AFM, injectors. Though my car makes around 40 rwkw more at the same boost.

I run Splitfires and only had an occasional misfire when using BCPR6ES plugs, but since changing to one heat range colder (the same as you are running) I've had no misfire issues.

I've got brand new Splitfires with BCPR7ES (I think, or whatever Trent told me to get). On 18psi I still had a misfire. Gapped them to about .6mm and they are all good.

I think you should be aware that results with coilpacks and plugs seem to vary quite greatly on RBs for some reason. Two people can have identical set ups but have two very different experiences. There's obviously something else in play, but plug gaps are the only known fix as far as I am aware.

before reading replies i figured out how to put the gap back up haha i found my round medallion tool and used that. i checked 2 spark plugs and the gap was 0.75mm ..they were supposed to be 0.9mm. unless im measuring it wrong but i span the medallion around carefully till it stopped moving and its where it landed.

i'll do the rest tomorrow so i can see what im doing lol

There's obviously something else in play, but plug gaps are the only known fix as far as I am aware.[/background]

Only known fix? There are several ways that could fix the problem other than gapping down the plugs.

It could be a poor engine or coilpack loom. Or the engine earth could be the problem. Also the connection to the spark plug within the coil pack and the coil pack plug itself could be the issue - though this is easily fixed by cleaning the coilpack and using dielectric grease.

By gapping the plugs down, you are trading off low throttle performance and economy, and the car will make more power through the rev range with the largest gap you can get away with running.

So yes everyone's engine is in different levels of condition, but I'd fix the underlying problem rather than living with gapped down plugs.

yeah im just gapping them down for a temporary fix, didnt realise you lose low throttle response though :( car is already poor on petrol lol lucky to get 300km out of a full a tank .

coilpack loom look looks like new from my untrained eyes.

coilpacks look very clean i took two of them off earlier, i didnt use dielectric grease though i'll lhave to look into that

I find they're ok on the dyno whilst I'm tuning, great for street use.. as soon as I hit the track and do a few laps.. bamm misfire city!

But at 0.5mm it's tits.. no misfires at all!!!

Interesting

My old splitfires died recently (this was not a gap issue, they were breaking down nearly on idle. Must have had at least 1 no good coil) so i have a brand new set in now

Might gap the plugs a bit lower next time to be safe. Although its only a street car and havent really had any dramas before on 0.8

Interesting

My old splitfires died recently (this was not a gap issue, they were breaking down nearly on idle. Must have had at least 1 no good coil) so i have a brand new set in now

Might gap the plugs a bit lower next time to be safe. Although its only a street car and havent really had any dramas before on 0.8

How long did they last if you don't mind me asking?

update on the ebay dude:If it is a faulty coil then it would only be 1. It wouldn't be all 6 at the same time.

This alone is an extremely rare occurrence as a lot of care goes into these coils during the manufacturing process.

We will need isolate the single faulty coil though so it can be replaced under warranty.

Thanks.

whats my reply going to be ? should i go for replacements or keep insisting on a refund. to me replacing them is more hassle and seems a waste of time if they're going to keep failing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...