Jump to content
SAU Community

Recommended Posts

  • Replies 135
  • Created
  • Last Reply

Top Posters In This Topic

LOL...if they are issues, then certainly get them sorted before blasting around the circuit, if its because they are std...thendont worry, std is fine...just get out there and give it a blast.

Any chance of a Fri or Sat night dinner to catch up with SAU-SA folk

LOL...if they are issues, then certainly get them sorted before blasting around the circuit, if its because they are std...thendont worry, std is fine...just get out there and give it a blast.

just gotta replace tie rod ends, lock hicas, replace rear cradle bushes, get rear camber kit, then it'll be all ready to go :D

Any chance of a Fri or Sat night dinner to catch up with SAU-SA folk

im sure we can organise something :( the last cruise we had, the idea of a track day was mentioned and there was a lot of interest. anyone else keen on the track day?

Edited by Sambo33

Is it best to sort accom near the track or in Adelaide, as the soone ri boot accomn around Nth Adelaide the cheaper we get it. I guess its a 2-3 hr drive to the track, may leave mega early Sat morning and go straight to the track, that way Sat night will be cheap as well because two beers and i will be out cold

Edited by Roy

At the minute a token Skyline is driving over from vic to do a Practice day at Mallala.

Its basically an open day at the circuit for ppl to drive their cars.

From their website ...

Cars and bikes Practice Days - start time 10.30 a.m. - gates open at 10 a.m.

- 15 minute sessions are run for each category with 5 sessions per day

- Motorcycles – fast

- Motorcycles – slow

- Closed cars

- Open cars

The day finishes with the final session at 4 p.m. or 4.30 p.m. The cost per day is $70.00 for cars(these charges include GST)

Drivers of cars need a hemet, and clothing (not synthetic) that is full length leg and sleeve coverage.

This is different to Drift Practice Days, and at most tracks its kinda frowned upon going sideways everywhere smoking up your tyres when their are cars around you that are "race cars" looking to do setup work etc.

I have never been to one of the Mallala ones before, but they are a practice day for the full circuit and usually provide a great opportunity to get out and have some fun.

if your all not too scared of a little high speed drift, come down the Adelaide International Raceway on the 11th September opens at 10 (i think)

there using the d-nats layout so you hit the esses's in 4th gear so its pretty quick sliding

they are also opening up the back of the bowl so drifting onto the drag strip will be allowed..

gonna be an awsome day.. im already getting tyres sorted so if your all keen get crackin on tyres as AIR has a tendency to rip tyres to pieces in less than 2 laps

should be fun

Sam.

just gotta replace tie rod ends, lock hicas, replace rear cradle bushes, get rear camber kit, then it'll be all ready to go :(

im sure we can organise something :( the last cruise we had, the idea of a track day was mentioned and there was a lot of interest. anyone else keen on the track day?

i'd definitely be keen on a track day! As long as the cars on the road!

I wouldnt mind getting together with some sau-vic boys and having a get together/drink/eat session. keen?

Well at the moment it seems there is only me, and the possibility of the SAU-Vic Trackday cheer leader Bec. When i see them ill be working on the others too... and a session constitutes a good 12 hours on the drink :D

if your all not too scared of a little high speed drift, come down the Adelaide International Raceway on the 11th September   opens at 10 (i think)

Pass....there is a day at Winton that weekend...plus i think your mad to drift your daily driver, but daily drivers are fine for circuit work...well in my eyes anyway. :D

So Mallala is like Calder where they only open a few corners for drifting?

Edited by Roy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...