Jump to content
SAU Community

Fixing The Rear Camber And Ride Height

alexboland
 Share

Recommended Posts

alexboland Explorer

alexboland

Posted
Posted

post-142398-0-96930500-1454458988_thumb.jpg

Hey guys

How do i fix the rear camber and raise the ride height? As you can see with the setup i have now the tires dont fit the rims because the car is lowered too much and there is some camber. The front tires are the same but with coilovers so i think i can fix them up its just the back ones that are the problem.

Any advice would be most appreciated thanks.

GH05T Grand Master

GH05T

Posted
Posted (edited)

...........wut

the tires dont fit the rims because the car is lowered?

what are you trying to fix? do you want negative camber to fit wide wheels under a low car?

camber is the only thing squeezing the wheels (which are either too wide or the wrong offset however you look at it, you aint fixing that without new wheels) under the car.

raising it will reduce some natural camber but then your wheels are going to poke out more.

do do you want to raise the car and remove the negative camber?

that pick tells us nothing, also what is your current setup? wheels specs, what has been changed?

what suspension components are you using? do you have adjustable things like coilovers or adjustable camber arms ect.

Edited by GH05T
alexboland Explorer

alexboland

Posted
  • Author
Posted

i want to fix the camber and be able to fit tyres onto the rims without having them stretched. The tyres that are on the wheels atm are stretched. The front has coilovers not sure about the back. I dont have adjustable camber arms but im looking into buying some for the back. Im not sure what the wheel specs are. Basically what i want to know is what do i need to fix the rear camber and how to fit the tyres properly.

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

Sell wheels and buy wheels that fit within the guards.

Get adjustable upper arms to adjust camber. You may get away with adjustable bushes (e.g. Whiteline).

You may have to get new suspension (or second hand rear struts, but who know what will happen to your handling).

GH05T Grand Master

GH05T

Posted
Posted (edited)

take the wheels off and see whats been installed, if you have excessive negative camber it may have aftermarket camber arms already, i cant see from that pick but it may be from being too low.

and are you saying its got coilovers in the front but nor rear and is low all round? thats a bad combo.

nothing is going to make those wheels fit though, bigger tires (which may be more suited to the wheels) are never going to fit the car, you can bandaid an offset too high but not too low, those wheels do not fit period.

do this:

- new wheels that fit the car.

- "if" the aftermarket suspension is adjustable raise it back up or,

- get coilovers, stock structs or new suspension to suit the height you want and get the car to the required height (good move)

- IF the camber is still too negative get new camber arms to suit (probably stock)

Edited by GH05T
alexboland Explorer

alexboland

Posted
  • Author
Posted

Thanks for the advice guys. A shame nothing can be done for the wheels i have now though. I thought i could put coilovers on the back and raise the height so that bigger tyres can fit the rims.

GTSBoy Grand Master

GTSBoy

Posted
Posted

Well you could do as you say. Raise the height so the tyres don't foul the guards at rest then fit tbigger tyres. But just as the boys said above, they will now poke put even more, especially if you also wind off some camber. And they will probably still foul the guards on bump.

MrStabby Grand Master

MrStabby

Posted
Posted

Yeah you have the wrong wheels - sell them and get something with a sensible offset. There's no other solution. As an added bonus you wont have to worry about getting defected any time a cop pulls you over. :yes:

Ecozile Contributor

Ecozile

Posted
Posted

If you want to keep the current wheels, you can look at wider guards or rolling the guards.

Have a look in there in case if PO has installed spacers.

Fixing camber at that height will bring the top edge of the tyre closer to the wheel arch.

GTRPSI Mentor

GTRPSI

Posted
Posted

Adjustable lower and upper arms can help you bring in the wheels a little if they dont rub on the inside.

The CV joints can slide in more if needed, but dont go too far.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...