Jump to content
SAU Community

Recommended Posts

post-142398-0-96930500-1454458988_thumb.jpg

Hey guys

How do i fix the rear camber and raise the ride height? As you can see with the setup i have now the tires dont fit the rims because the car is lowered too much and there is some camber. The front tires are the same but with coilovers so i think i can fix them up its just the back ones that are the problem.

Any advice would be most appreciated thanks.

...........wut

the tires dont fit the rims because the car is lowered?

what are you trying to fix? do you want negative camber to fit wide wheels under a low car?

camber is the only thing squeezing the wheels (which are either too wide or the wrong offset however you look at it, you aint fixing that without new wheels) under the car.

raising it will reduce some natural camber but then your wheels are going to poke out more.

do do you want to raise the car and remove the negative camber?

that pick tells us nothing, also what is your current setup? wheels specs, what has been changed?

what suspension components are you using? do you have adjustable things like coilovers or adjustable camber arms ect.

Edited by GH05T

i want to fix the camber and be able to fit tyres onto the rims without having them stretched. The tyres that are on the wheels atm are stretched. The front has coilovers not sure about the back. I dont have adjustable camber arms but im looking into buying some for the back. Im not sure what the wheel specs are. Basically what i want to know is what do i need to fix the rear camber and how to fit the tyres properly.

Sell wheels and buy wheels that fit within the guards.

Get adjustable upper arms to adjust camber. You may get away with adjustable bushes (e.g. Whiteline).

You may have to get new suspension (or second hand rear struts, but who know what will happen to your handling).

take the wheels off and see whats been installed, if you have excessive negative camber it may have aftermarket camber arms already, i cant see from that pick but it may be from being too low.

and are you saying its got coilovers in the front but nor rear and is low all round? thats a bad combo.

nothing is going to make those wheels fit though, bigger tires (which may be more suited to the wheels) are never going to fit the car, you can bandaid an offset too high but not too low, those wheels do not fit period.

do this:

- new wheels that fit the car.

- "if" the aftermarket suspension is adjustable raise it back up or,

- get coilovers, stock structs or new suspension to suit the height you want and get the car to the required height (good move)

- IF the camber is still too negative get new camber arms to suit (probably stock)

Edited by GH05T

Thanks for the advice guys. A shame nothing can be done for the wheels i have now though. I thought i could put coilovers on the back and raise the height so that bigger tyres can fit the rims.

Well you could do as you say. Raise the height so the tyres don't foul the guards at rest then fit tbigger tyres. But just as the boys said above, they will now poke put even more, especially if you also wind off some camber. And they will probably still foul the guards on bump.

Yeah you have the wrong wheels - sell them and get something with a sensible offset. There's no other solution. As an added bonus you wont have to worry about getting defected any time a cop pulls you over. :yes:

If you want to keep the current wheels, you can look at wider guards or rolling the guards.

Have a look in there in case if PO has installed spacers.

Fixing camber at that height will bring the top edge of the tyre closer to the wheel arch.

Adjustable lower and upper arms can help you bring in the wheels a little if they dont rub on the inside.

The CV joints can slide in more if needed, but dont go too far.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...