Jump to content
SAU Community

Recommended Posts

I drove 1500km to get to the dyno and the car had developed a high idle after about 1200km of driving that day. Prior to that it was 1100 cold, 850-900 once warm. But when I got down to be tuned it was 1100 all the time. Not lumpy, just a smooth 1100. I couldn't be 100% that it was checked or it was assumed to be correct.

Whatever the case may be, I'm back in the middle of nowhere with little in the way of options other than to drive back down there or truck it. Not like I can just drop it off at a workshop for the day. Either that or fly someone here to look it over.

Surely there is someone there local that can help you find a vacuum leak, hoses, gaskets especially the inlet manifold gasket maybe try pressurising it through your intercooler with the car off see if you can hear leaks or try http://www.sau.com.au/forums/index.php?/topic/110431-Diy-Aac-Valve-Cleaning-&-Idle-Reset.

And please tell me you didn't drive your car for that distance on the power fc base map

Edited by mr skidz

No it wasn't base map, it had been tuned a year ago and had been adjusted via the hand controller using my wideband recently.

Finding a vac leak isn't an issue, having it re-tuned is. I traveled halfway across the country and may well have to do it again.

Standard cas. He said it would only take 7 degrees and was expecting 12 or more. Power does seem low for the turbo but torque seems to be ok. Car made 263rwkw and 750nm of torque. Mainline dyno.

I'll have to pull the dump off and check that out Tao. If that's the case, I will drag out the die grinder and open it up a little and make sure it's all nice and smooth.

Thats about right, we have had a few on pump not able to crack 270, same thing timing limited. It works mint on E85 but unless you have a killer exhaust manifold and cooler it will struggle.

Might be time for an exhaust manifold and bigger exhaust then if that's the case.

Thanks for your input.

Tap a fitting into ex manifold and measure the pressure, i bet its crazy high

  • Like 1

Have purchased datalogit, just going to source some knock detection gear and see what is what I guess. I'm going to throw some more fuel in at wot, even if it is "rich", I'll feel better for it. And the amount of time is spend in that region it won't hurt my economy much.

Tap a fitting into ex manifold and measure the pressure, i bet its crazy high

Lol I have no doubt you'd be right there

For reference I have an Hypergear SS2, standard manifold opened up and port matched, bell mouth dump opened up and port matched as close as possible, 200cell cat and 2 straight through mufflers in 3 inch piping and I get 0.5psi back pressure max. I pulled heaps of metal out of the bell mouth entry. Well worth a look at yours to rule that out.

  • Like 1

Cheers. Yeah when I get some time I'll pull everything off and whip out the die grinder. Exhaust only has a mid muffler and rear cannon. Was considering removing the mid muffler or replacing it with something that is documented to flow more than I need. I'm willing to got 3.5 inch cat back if that's what it takes. I'm not worried about noise, as long as it doesn't drone

For reference I have an Hypergear SS2, standard manifold opened up and port matched, bell mouth dump opened up and port matched as close as possible, 200cell cat and 2 straight through mufflers in 3 inch piping and I get 0.5psi back pressure max. I pulled heaps of metal out of the bell mouth entry. Well worth a look at yours to rule that out.

We're not talking about back pressure in the exhaust pipe. We're talking in the MANIFOLD. On a street car you will find it will be up to double the boost pressure.

We're not talking about back pressure in the exhaust pipe. We're talking in the MANIFOLD. On a street car you will find it will be up to double the boost pressure.

I realised after posting that's what Trent would have meant, I saw the comments about the dump pipe and misunderstood.

Still have an issue with having to hold the throttle open on cold start for it not to die, I'm thinking this may be an iacv adjustment that'll fix that

That's pretty poor form from a tuner.

Could also be mixture related, once you get a wideband on, it should provide you with more insight on what's going on.

Close to stoich or stoich on a cold motor, will stall, too rich on a cold motor will stall.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...