Jump to content
SAU Community

Recommended Posts

hey guys, need to sell my wheels,

 

 

 

 

Nismo LMGT4 by rays, 18x9.5+12 all round, tyres are 225 federal 595 at the front and basically new Achilles ATR sport 265 at the rear - not going to remove tyres

 

 

 

 

 

condition is ok but some rashing, mainly due to the rubbish paint job Import Monster did on these, they were originally white

 

 

 

 

 

anyway the price reflects the rashing, apart from those scratches they are good

 

 

 

 

 

if they don't sell ill wash em and take some better photos, but please, someone just buy them dont make me wash them god

 

 

 

 

 

$2500 SHIPPED

 

 

pEudGFWl.jpg

 

 

WH9NPodl.jpg

 

 

LfHQwcpl.jpg

 

 

JnhPTh2l.jpg

 

 

y187AiWl.jpg

 

 

qzyOETrl.jpg

 

 

nXgGRq3l.jpg

 

 

oWlklqql.jpg

 

 

ka6Jd3xl.jpg

 

 

CF1WzQZl.jpg

 

 

AJEWmUQl.jpg

 

 

Qi3OhLSl.jpg

 

 

vLmwqOkl.jpg

 

 

bUJpRu1l.jpg

 

 

 

 

 

full album

 

 

 

  • 4 months later...
  • 2 weeks later...
  • 4 months later...

For 550 extra for refurbishment these will look like new! Factor that in and the cash you get as a present will turn this into a fine investment. Stickers from ebay. 

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...