Jump to content
SAU Community

Recommended Posts

Hi everyone

About to replace spark plugs on R34 GTR.

Car is pretty much stock so was just looking to replace with the stock plugs (I.e. NGK PFR6A-11) but also came across Bosch (8153-6).

Anyone here ever run the Bosch 8153-6 plugs as they are about half the cost of the NGK's?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/464181-spark-plugs-r34-gtr/
Share on other sites

If they are listed as a direct replacement then they will be fine. Should be a reference chart on the web somewhere that will tell you.

Yep, try this one:

http://www.angelfire.com/extreme4/skidoolympique/SPARK_PLUG_CROSS_REFERENCE.htm

Says Bosch equivalent is FR8DCX

See line 1257

That's all that's in mine Chris, I plan to just swap them out every service or 2 given how cheap and easy to get they are.

No misfire issues with spitfires and those plugs at 330or so rwkw.

For a street car they'll be fine.

If they are listed as a direct replacement then they will be fine. Should be a reference chart on the web somewhere that will tell you.

Yep, try this one:

http://www.angelfire.com/extreme4/skidoolympique/SPARK_PLUG_CROSS_REFERENCE.htm

Says Bosch equivalent is FR8DCX

See line 1257

Strange it comes up with FR8DCX. This was the Bosch catalogue page at Supercheap Auto. post-91000-14605255392572_thumb.jpgpost-91000-14605255571854_thumb.jpg

The package for 8153-6 also shows FR6KPP33X+

Not interested in going copper plugs but thanks.

For me it's coppers every time.

I bought mine from here, about $3.00 a shot. Add some filters to the order to reach $50 and it's free delivery.

https://www.sparesbox.com.au/spark-plugs-ignition

But whatever plug you choose, check the protrusion from the head. Give the spring in the coil pack a bit of a tug to make sure it contacts the conductor.

ISO dimension plugs are a bit shorter than "normal".

Hmmm sounds like the coppers are the way to go. Maybe I'll be a convert. Just out of interest, should I just stick with the stock plug gap of 1.1 and heat range of 6? Car is fairly stock with cat back, boost restrictor removed (running 1 bar) and arc induction box.

I was using 7's but fouled a set after only a few k. Probably due to letting the car idle too long with the ac on during the summer. I've recently been running 6's and changing to 7's when tracking. I'll go back to 7's and see what happens. CBF changing plugs all the time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...