Jump to content
SAU Community

Recommended Posts

Hello fellow SAU'ers,

After a bit of advice on my R34 GTT that had just overheated last Thursday suddenly, to the point of the H-line on the water temp (I panicked so bad) and what my first course of safe action should be?

Problem: overheating according to high water temp and oil temp at half way on stock gauges

Observation: overflow tank full (but dirty), no coolant in radiator which I checked tonight as I've not been driving it since, water pump and thermo replaced at 110k, I am the second owner now at 170k - I have the original service papers to back this up. No visible leaks, although after hours of driving on Thursday, noticed leaks when coming home, I was stuck for time but at a quick glance have not noticed any cracked or burst hoses and thought this may have just been the overflow kicking in.

Action: I have a new Nissan thermostat to go in, was initially going to remove my rad, take it to Natrad for flushing/cleaning, bleeding the system (myself) with distilled water and whatnot at the same time and replacing the thermostat (myself) also.

Would this be a safe route to take before just handing over the whole car to NatRad and them slugging me $600 when I could have just fixed, eliminated or even alleviated some of my problems?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/466314-gtt-overheating-recovery-steps/
Share on other sites

I boiled mine couple of weeks ago at the track, turned out to be a leaking water temp gauge sensor mount that spat out just enough coolant for the system to start running dry.

Here were some of the theories thrown around originally: http://www.sau.com.au/forums/topic/463353-post-track-day-qs-rotor-wear-gearbox-oil-ps-pump-manifold-nuts/?do=findComment&comment=7762451

If you're not in a rush you could try bleeding the system thoroughly yourself and carefully checking for leaks before taking it in?

Overflow bottle full and no visible water in radiator. Try a new radiator cap as a quick fix and hope remedy. It sounds like the cap is letting the coolant go to the o/f and then engine is getting too hot. good luck and hope it's a simple fix.

On 15 August 2016 at 10:55 PM, admS15 said:

Overflow bottle full and no visible water in radiator. Try a new radiator cap as a quick fix and hope remedy. It sounds like the cap is letting the coolant go to the o/f and then engine is getting too hot. good luck and hope it's a simple fix.

Will try this and report back - mates are saying it could even be a head gasket? Seriously?

Defintely still running fine, no white smoke etc. possibility?

Will try this and report back - mates are saying it could even be a head gasket? Seriously?

Defintely still running fine, no white smoke etc. possibility?


It can be a Hg but you would want to investigate all other possibilities first as Hg is a pita to replace. Try the cap and let us know. Fingers crossed for you mate.

My NEO motor in a manual stagea was overheating also. It turned out to be a small leak in the plastic end tanks of the stock rad. Was only enough to lower the system pressure and then the coolant would boil at the turbo and the car would then overheat. Check that your hoses are hard with pressure when it overheats. If they are not, then you have a small leak somewhere. I replaced the rad cap and thermostat before i found the leak and it did nothing. A full aluminum rad from just jap or ebay is an easy job you can do at home if that is your problem. By the way, when looking for coolant leaks, you may not see any fluid, only the white residue of the boiled dry coolant. Look for that instead of liquid coolant. Hope its not your head gasket, you can test for CO2 in your coolant with a tester from repco. Or if its bad enough, you will have bubbles coming to the surface with rad cap off and car idleing. You may also have oil in your coolant or froth in your oil. Look for that. Good luck.

  • Like 1
  • 3 weeks later...

Rad is absolutely cactus.

Not having much luck finding an aftermarket replacement for auto, that fits the stock shroud, and has the two oil cooler nubs for the auto box.

5 hours ago, MrStabby said:

Cactus as in blocked? You could try having it cleaned (repaired?) by a pro. They should be able to tell you how well it comes up after.

As in full of little dents and creases, full of dirt and bugs and there's a huge black area like it's burnt out.

Ive got a JJR OEM style replacement on the way I'll fit tomorrow and report back.

Alright gents, new JJR OEM rad, replaced thermostat & rap cap, full coolant flush, replace and system bleed has rectified my overheating problems (so far, need some warmer weather to really trial this).

 

hopefully this will help anyone else with this problem and not to immediately jump to a head gasket conclusion

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...