Jump to content
SAU Community

Recommended Posts

Ok I'm starting this post to see what is working for everyone.

My new engine is a 3025 neo built engine and I want to maximize its performance. 

Old system is a 3inch turbo back 100 cel cat straight through muffler.

Was thinking about doing a 4inch dump pipe to 3 inch from dump back.

 

Link to comment
https://www.sau.com.au/forums/topic/466345-exhaust-system-setups/
Share on other sites

You don't need anything crazy if you venting gate to atmo and run no cat..

If you not..good luck with that .., just take of exhaust on dyno before you piss fart around remaking stuff

400 should be a walk in the park for a 3 inch exhaust..

cheers

darren

Edited by jet_r31

The smart* approach (fully fully custom) is to route the wastegate pipe back in behind the cat.  Face it, the gate is not open very much of the time on the street, therefore the vast majority of the time all the gas is going through the cat.  Then when you really need the gate to flow lots of gas, you're not also requiring the cat to flow lots of gas.  Win.  Was it dose pipe Johnny who's done basically this recently?

 

*Only smart until you actually do get some sort of EPA/police attention, in which case it's not actually legal.

1 hour ago, GTSBoy said:

The smart* approach (fully fully custom) is to route the wastegate pipe back in behind the cat.  Face it, the gate is not open very much of the time on the street, therefore the vast majority of the time all the gas is going through the cat.  Then when you really need the gate to flow lots of gas, you're not also requiring the cat to flow lots of gas.  Win.  Was it dose pipe Johnny who's done basically this recently?

 

*Only smart until you actually do get some sort of EPA/police attention, in which case it's not actually legal.

Yes Johnny did this and ive copied plus merged it later for good measure ?

3 hours ago, lcxu105 said:

So a 3 1/2"dump 700mm lone back to a straight through 3"with 100 cel cat with 50mm wastegate merged back in the 3" pipe should be able to handle 420 to 450rwkw?

i had a 3.5 inch dump, then a 3 inch with a slight offset lukey and a resonator on my r31. It ran 141mph through the mufflers on 25psi with a auto

it was quiet exhaust but with a vented gate 

My mate had same mufflers in his vl turbo( manual)  as he copied with a 3582 turbo on upper 27psi, but with a 3 inch dump..he ran 138mph (you work the power out out) on a 3582 1.06 turbo , he dropped the exhaust  at dump and it made 10rwkw difference...Had a vented gate

No meows..

 

It really really comes down to vented gate..if you don't vent it..good luck. You need a f**koff big exhaust. Just like a Gtr with the twins replaced with upgrades...

or perhaps merge it a long way back. But thats a p.i.t.a

honestly you just need to test it, as different mufflers and cats pose different restrictions..even in same sizing..

cheers

darren

 

  • Like 1

Interested to see what difference venting the gate to atmosphere would make with my set up. Currently running a 4" dump to the bellhousing and then 3" from there through a single round muffler after the diff. Single cam RB30 with a powerglide. Head is stock besides slightly oversize valves and a small 218 @ .050 wade cam. Making 396rwkw with a 1.06 gtx35 on 30psi. Basically stopped making decent gains in power with more boost and inlet temps rising quite fast. The gate plumbs back in maybe halfway down the dump pipe. Would it be much more efficient going to atmosphere as I presume a fair amount exhaust flow would be through the turbo at that boost level?

I didn't have a chance to dump the exhaust last time on the dyno to see if any gains were to be made but I guess the stock ports in the head would be holding things back a little also?

44 minutes ago, PSI086 said:

Interested to see what difference venting the gate to atmosphere would make with my set up. Currently running a 4" dump to the bellhousing and then 3" from there through a single round muffler after the diff. Single cam RB30 with a powerglide. Head is stock besides slightly oversize valves and a small 218 @ .050 wade cam. Making 396rwkw with a 1.06 gtx35 on 30psi. Basically stopped making decent gains in power with more boost and inlet temps rising quite fast. The gate plumbs back in maybe halfway down the dump pipe. Would it be much more efficient going to atmosphere as I presume a fair amount exhaust flow would be through the turbo at that boost level?

I didn't have a chance to dump the exhaust last time on the dyno to see if any gains were to be made but I guess the stock ports in the head would be holding things back a little also?

What fuel are you running? 30psi i would expect to see more hp than that 

On 8/24/2016 at 7:10 PM, PSI086 said:

Interested to see what difference venting the gate to atmosphere would make with my set up. Currently running a 4" dump to the bellhousing and then 3" from there through a single round muffler after the diff. Single cam RB30 with a powerglide. Head is stock besides slightly oversize valves and a small 218 @ .050 wade cam. Making 396rwkw with a 1.06 gtx35 on 30psi. Basically stopped making decent gains in power with more boost and inlet temps rising quite fast. The gate plumbs back in maybe halfway down the dump pipe. Would it be much more efficient going to atmosphere as I presume a fair amount exhaust flow would be through the turbo at that boost level?

I didn't have a chance to dump the exhaust last time on the dyno to see if any gains were to be made but I guess the stock ports in the head would be holding things back a little also?

I wrote a big post and it didnt work. Cbf again

My mate morgz on ct ran 3 inch dump/exhaust plumbed back

With a 3582 with billet 67mm  comp 1.06

Went 10.20@140 -30psi-auto-450rwkw..made no more power

He unplumbed gate and it went straight to 40psi and maxed fuel system out in the midrange where peak torque is. Had to plumb it back..lol

So maybe worth a look

Cheers

Darren

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...