Jump to content
SAU Community

Recommended Posts

Tomei oil pump failures

I tried searching but ran across the spline drive oil pump conversions and hadn't really heard bad press about the Tomei oil pump until then. I read about ONE failure so far and the thread did not provide Tomei's resolution to the pump issue so I'm curious if this is actually a potential problem or not.

I have a Tomei pump and am curious if anyone has seen one broken and under what circumstances. I'm limiting my car to 8k, but I do bang the limiter quite frequently and was just thinking about going a bit higher soon. Some say the cause of failure is oil cavitation from temporarily starving the pump (which means a dry sump would be the only real cure), and some say it's simply the 2-flat-drive stock pump orientation that kills oil pumps. I'm looking for actual evidence if possible because I'd like to live the rest of my engine's life in a happy state of knowing the chances of oil pump failure are very slim.

Patrick

Link to comment
https://www.sau.com.au/forums/topic/468441-tomei-oil-pump-failures/
Share on other sites

If that Tomei pump failure was with the spline drive fitted then there lies your answer. They will not tolerate any misalignment and will load the driven gear radially and also fretting/galling on the splines. 

Nitto wrote a good answer somewhere on here why they will not release a spline drive yet due to reliability issues.  

You have the stroker crank with full width pump drive I guess, what sort of balancer are you running. I've been running a  1000hp ATi for a long time now, and when I pulled it all down for some checking last year it was all good with minimal wear thanks to ATI, but no limit bouncing here.  .

However if you like bouncing on the limiter a bit then something will eventually give ...dry sump it and you can bounce of the limiter all day long :devil: 

I have never heard of a Tomei pump failing (which is not to say it doesn't happen). If you fit oil restrictors when you fit the pump and you overfill the sump by a litre OR preferably have an enlarged sump there is no reason why your pump should starve (i.e. a dry sump is not mandatory).Stop limiter bashing. Raise the limit on your ecu (I assume you have an aftermarket one) and put a stop under you accelerator pedal or adjust the limit stop (depending on your set up) to limit the revs.

I do have Tomei head restrictor, Greddy Sump (Which the Tomei tells you quite clearly you shouldn't run in some of it's settings without a larger sump), and N1 block (which has larger drain ports back to the pan), also mine's baffles and rear "drain" if anyone cares about that anymore. And I'm on the Fluidampr balancer (seems really nice).

Also yes Haltech...I hit the 2 step limiter when launching everytime but if I spin the tires the car racks out so fast in first that it hits the limiter quite quick on top. It IS a soft touch limiter though which at least isn't as hard as a hard cut. I'll bump the revs to 8500-8700 and use Haltech to output a shift light and try to just stay off of it. But yes thanks for the info. Also I do have the Haltech reading oil pressure and use the "engine protection" feature to put it in limp mode when it senses oil pressure low or high out of range.

I'm not sure the guy was spline drive, but I ran across the thread (not on this forum) after someone asked me if I had converted mine to spline drive.

And yes BC billet stroker crank. Engine runs really smooth with the balancer, crank, heavier nismo coppermix, etc.

Thanks!

  • 1 year later...

They have in some cases become oval and caused binding and lock up of the oil pump. Nothing to do with Spline Drive. We do however have Spline Drive upgrades for most pumps and the theory they bind due to crank flex is just a myth. Both ourselves Supertec and Spool have been selling these for the past 4 years. Zero gear failures reported to date for our kits.

 

 

C56E711E-FA3A-4E79-89F7-294A0BF02C53.jpeg

Edited by Frracer
  • 5 months later...
On 1/4/2017 at 3:10 AM, Meathead said:

If that Tomei pump failure was with the spline drive fitted then there lies your answer. They will not tolerate any misalignment and will load the driven gear radially and also fretting/galling on the splines. 

Nitto wrote a good answer somewhere on here why they will not release a spline drive yet due to reliability issues.  

You have the stroker crank with full width pump drive I guess, what sort of balancer are you running. I've been running a  1000hp ATi for a long time now, and when I pulled it all down for some checking last year it was all good with minimal wear thanks to ATI, but no limit bouncing here.  .

However if you like bouncing on the limiter a bit then something will eventually give ...dry sump it and you can bounce of the limiter all day long :devil: 

Nitto are not the authoritative answer on oil pumps or spline drives. Can respect their own findings maybe it wasn’t so successful based on what clearances and spline profile they tested with. We carried out our own R&D prior to launching them in 2014. We have successfully been selling spline drive kits for almost 5 years now with over 900 kits sold and yet to see the “Nitto theory” come to life..... Ironically our Jun kit fits the Nitto pump. Have a good few customers running a Nitto pump with a spline kit. That in my view is an anwesome pump because Nitto did use better materials and a billet 7075 back plate compared to Jun/Greddy.

Edited by Frracer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...