Jump to content
SAU Community

Recommended Posts

That's an expensive set of nice wheels. Don't spoil it by putting stupidly narrow stretched tyres like some people do!

Something like 285 35 may do the job. If the tyres stick out too much make the guards bigger don't shrink the tyres!

  • Like 6
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7821762
Share on other sites

I ran 275x35x19 on my R34 GTR (work d9r 19 x 10.5 +15), which is mildly lowered. I couldn't go full lock without scrubbing on the inner guard linings on both sides.

I went down to a 275x30x19 tyre and used a heat gun on my inner linings. No scrub whatsoever now.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7822513
Share on other sites

9 minutes ago, OV33RR said:

275/35r19 there pretty big dont think id like to go bigger scrubbing as it is

I understand - but then why go 10.5 wide if your not going to put the appropriate tire on there.

The below is 10 wide with a 285 - see how the sidewall is square - surely that will give the car better turning and handling - please someone correct me if I'm wrong. 

IMG_1513.JPG

  • Like 4
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7824201
Share on other sites

  • 2 months later...
16 hours ago, vxsr33 said:

From what i have read 275 or 285 is the recommended width for a 10.5 inch rim. 275 on a 9 inch rim isn't recommended as its too wide.

275 on 9in wheels are within the LVTA guidelines but the proof of the pudding is in the photos - OPs tyres are clearly stretched and the above 285s on 10 in wheels look just right.

Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7838260
Share on other sites

  • 3 weeks later...

I've got the same wheels offset etc, previously I had 275/30 no scrubbing now I have 275/35 19's nitto nt05 scrub the inner and outer guard. Then again mine isn't ride height, I wouldn't go anything thicker then the 30 series unless u want to do some suspension and camber work. My front is at 3 degrees camber to prevent my guards ripping again.

 

Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7841048
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 21 is explicitly the coils detected as the issue. Is it guaranteed the actual issue? No. Just the ECU thinks it is. When you say rattling, describe it better, get an audio clip as best you can if possible.
    • Yea got me coppers. Bad news is I just put them in and the car still has the light and shakes. I also noticed I hear like rattling coming from the exhaust piping right under me. Does 21 also have a possibility of being O2 sensors?   So, coil packs are good, the harness is good, the MAF is working, and obviously the spark plugs just replaced and working.
    • Make sure you drop the GTT base tune back in, and set your injectors again, this will remove anything playing up with it you may have removed. Possibly lean there as it's normally a fast transient going THROUGH atmospheric pressure, and a turbo motor would then quickly go richer as boost builds. The only worry you MIGHT have is ignition timing, as the DE is higher compression than the DET from memory. But again, you're not in boost, so the DE motor will be a lot more forgiving at atmospheric.   Get Murray, Kinkstahs, and Johnny's input on tuning haltechs, those guys have played with tuning enough in the past to be able to help now you're past the trouble shooting stage of the MAP issue
    • @Rusty NutshI mate. Do you have a pinout diagram for the na neo auto ecu? 
    • Yeah thats the plan now. 🤞
×
×
  • Create New...