Jump to content
SAU Community

Brake Lights Staying On

Shyboy

By Shyboy,
in General Maintenance

 Share

Recommended Posts

Shyboy Collaborator

Shyboy

Posted
Posted
Brake Lights Staying On

Brake lights staying on !!

 

Hi all

Just noticed my brake lights and wing light are stying on . Took it for a short drive then put it on stands to see if it brakes ok .It does. Checked all the fuses all fine . Took the battery off.

 

Any suggestion / ideas would be much appreciated

Cheers

Bruce

Link to comment
https://www.sau.com.au/forums/topic/470112-brake-lights-staying-on/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

They are controlled by a small, adjustable switch at the brake pedal.

First unplug the switch at the pedal and make sure the light goes off.  Assuming it does, push the switch a few times and see if it frees up, and if not it can be adjusted a little.  Otherwise it may just have failed and need replacing.

 

Shyboy Collaborator

Shyboy

Posted
  • Author
Posted

Yes it was the switch thank you.

Also found rubber/plastic button like bits on carpet which, I assume hits the switch ???

Seen the whole brake switch on Super cheap Auto would they fit ? or just find the rubbery end bit?

Thanks

 

Duncan Grand Master

Duncan

Posted
Posted

I'm not near the car to check, but this is the service manual page for it

brake-switch.jpg

It looks like a similar setup to my navara where the rubber stopper disintegrated a few years back leaving nothing for the switch to turn off against. Pretty sure I picked up the part at nissan for a few bucks after my dodgy fix failed again.

32_love Collaborator

32_love

Posted
Posted

This has happened to me in every import I've owned.

When that rubber piece brakes, I just super glue a five cent piece over the ensuing hole. Otherwise that switch doesn't get depressed when you let the brake off.

  • 1 year later...
mikel Community Regular

mikel

Posted
Posted

gotta love SAU!

My brake lights were on when I came home yesterday - figured it was most likely the switch, but did a search on SAU and bingo!

Even found the bits on the carpet, but wow it's tight under there :( - a quick look last night and another this morning, I was able to push the button in to prove the fault, but didn't have time to try an maneuver a 5c piece or similar in to activate the switch, or disconnect the connector...so the brake lights stayed on - got home tonight and the bulbs are blown - I should have disconnected them at the tail lights in the boot!

Not surprising in hindsight - cautionary tale - of course brake lights won't cop being on for 24hrs - they burn bright when required but aren't designed to stay on. At the time I was more concerned with flattening the battery, so had the battery charger on.

No biggy, bulbs are cheap...

I'm more concerned with the contortionist activity required under the dash to fix the switch - likely I'll have to remove the driver's seat to give me more room...

The glued 5c piece option sounds dodgy, but actually looks the best solution compared to swapping the switch assembly including disconnecting/reconnecting the connector...getting to it is tricky - admittedly I was holding a torch in one hand, so a fixed light source and 2 hands would help.

Is the rubber grommet piece available as a spare part - preferably without buying the whole switch? Pushing a new grommet in looks even easier than the glued 5c piece (not that anything is easy under the dash :( )

I'm wary of doing any mods to the braking system (or in this case the brake light system) - am I being too paranoid or appropriately cautious?

The car is not a daily and can stay off the road for a bit.

cheers

Mike

  • 2 weeks later...
mikel Community Regular

mikel

Posted
Posted

thanks goes to @Duncan for the diagram so I could get the clearance right when re-installing the switch, and @Dose Pipe Sutututu and @duffmansbrew for where to get the replacement bit ?

Biatch of a job under there - removing the switch makes it "easier".

I used a smidge of silicon grease on the hole to help the rubber bit slip in, and a flat blade screwdriver for a bit of leverage - it doesn't need force, it's just in an awkward spot.

Thanks again SAU!

 

cheers

Mike

 

  • Like 3
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
    • GTSBoy
      Strange issue RB25DET wont start

      By GTSBoy · Posted

      Yeah, I would have said the same. It makes me suggest that there are other things wrong, such that the ECU is totally unhappy with the broken sensor. The only other thought here is that maybe it is shorted, which might cause a different issue to the typical "disconnected" sensor.
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      The fact that US/JDM plates actually fit the skyline bumpers properly is a big, big thing for me as they are the correct dimensions. Annoyingly you can't opt for a normal plate (or plate combination) in that size. You have to make up your own one, and at that point you'd still know it wasn't randomly assigned. 
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      Well, really, that's any ECU, because it's not so much the ECU that the tuner connects to, but a laptop that's connected to the ECU. You have to have the tuning software installed locally. The "remote" part is essentially just remote desktop (RDP) or VNC type access. Nevertheless, if you're looking to upgrade, then you're immediately in the Haltech/Link territory, both of which can be done by any number of competent tuners here in Oz. But without a dyno, you'll definitely also need a wideband O2 sensor fitted, and you'll probably be relying on "auto" tuning a bit, where you drive it around under various loads and then apply the corrections that the ECU learns (basically applying the fuel trims that the ECU has to do to correct the mixtures). Tuning the timing is a little harder. It can be difficult to trust the old OEM knock sensors on RBs, so it is definitely best to have someone who knows what they're listening for, with knock ears (a piezo microphone connected to the engine, and and little amp and headphones so the listener can hear the angry men with hammers who live in the engine). That is more difficult to do remotely, and I suspect the only sane way is to be quite conservative on timing. But that's OK. You're probably waaaaay better off with conservative timing where you are. What is the fuel situation? 98RON available? Or low grade jungle juice?
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I see your point, I didn't think too deep into it, was purely focused on the price. There's no bad blood between myself and GSM, they acknowledged the price was cheaper else where and at the time couldn't match it. 
×
×
  • Create New...