Jump to content
SAU Community

Recommended Posts

16 hours ago, GTSBoy said:

Shafts are piss easy.  Fall out from the inside.  Hubs/splines are obviously much more trouble.  You need to dismantle all this to find out what is wrong with it before you go buying stuff though.

Ok cool figers crossed its just the shafts.

3 hours ago, hardsteppa said:

Having had  the same movement, i rebuilt the cv's, replaced bearings, new bushes, new diff centre with perfect backlash...i still have the same movement.  However..images.jpeg.8136256e0d9e64410795ed90d9daa444.jpeg

For real?  hope i dont play that game

I learnt from gts boy and stepper and did sfa and noticed no difference. Car drives fine with that type of movement, even at 240+ km/h. My advice is leave it alone unless the wheel is going in/out from bearing wear, that would require attention.

ok now watched the video...looked normal to me. Diffs don't have zero backlash, they have a small amount for a very good reason, which is visible as a bit of turn in the driveshaft like that, when not under load.

the 5 bolt driveshafts on the r33 gtst use a 5-ball cv joint in both the inner and outer, which for most purposes is as strong as fk, there's nothing in there to ' break' really, only wear a groove at best, unlike the 3x2 bolt shafts which I believe use a 3x ball bearing race on the inner. I rebuilt a spare set of shafts and they had exactly the same movementousness as my old ones, which when pulled apart had no visible wear. 

What I am getting at is if you're not having any ' issue' as such, the bit of movement like that is unlikely to be any concern. 

 

Ok maybe It's nothing, there's no bearing movement. Drives normal only thing i can think of is I get an odd click when taking off sometimes was thinking that could be related. Not continuous just once.

Here's a vid of it, car jacked up in neutral handbrake on.

 P1370539_2.mp4

Handbrake off in gear.

 P1370541_1_1.mp4

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...