Jump to content
SAU Community

Recommended Posts

My tuner also recommended I replace all the vacuum lines as well. Is there a site that sells direct replacements or perhaps a hose size chart for all the lines? I noticed on the drive home on slight occasions the steering wheel would vibrate, my buddy thinks it’s probably the rotors, thoughts

8 minutes ago, tridentt150v said:

Bingo!!!!

If you have coil overs and the car is down to the legal limit [100mm I think] then you will likely need adjustable uppers to get the alignment right.  Most [including mine] do.

And yes I’m on fortune auto 500 coilovers down 100% given my wheel size. Was hoping it would’ve been rotors given it’s much cheaper. But it is what it is. 

Buy FUCAs for R32 from GKTech (they are very good, but fiddly). Other option is the ones from UAS which recently had a group buy - I think someone is selling an older set (unused) on these very forums. I have both. Currently have the UAS ones on the car. I would not use anything else. All other available adjustable FUCAs for R32s are riddled with ball cancer and AIDS.

Buy GKTech upper CAs and traction arms for the rear. Or Hardrace. Best to get the rubber bushed Hardrace ones. GKTech only have spherical jointed options which are quite harsh and a lot less legal. Note that setting up and correctly adjusting rear uppers and traction rods is not as trivial as it looks. Search "bump steer".

Edited by GTSBoy
1 hour ago, GTSBoy said:

Buy FUCAs for R32 from GKTech (they are very good, but fiddly). Other option is the ones from UAS which recently had a group buy - I think someone is selling an older set (unused) on these very forums. I have both. Currently have the UAS ones on the car. I would not use anything else. All other available adjustable FUCAs for R32s are riddled with ball cancer and AIDS.

Buy GKTech upper CAs and traction arms for the rear. Or Hardrace. Best to get the rubber bushed Hardrace ones. GKTech only have spherical jointed options which are quite harsh and a lot less legal. Note that setting up and correctly adjusting rear uppers and traction rods is not as trivial as it looks. Search "bump steer".

 

 

they even made a video how to. Nice. 

1 hour ago, GTSBoy said:

Buy FUCAs for R32 from GKTech (they are very good, but fiddly). Other option is the ones from UAS which recently had a group buy - I think someone is selling an older set (unused) on these very forums. I have both. Currently have the UAS ones on the car. I would not use anything else. All other available adjustable FUCAs for R32s are riddled with ball cancer and AIDS.

Buy GKTech upper CAs and traction arms for the rear. Or Hardrace. Best to get the rubber bushed Hardrace ones. GKTech only have spherical jointed options which are quite harsh and a lot less legal. Note that setting up and correctly adjusting rear uppers and traction rods is not as trivial as it looks. Search "bump steer".

Is the hardened rubber pieces make the ride uncomfortable?

No. The steel on steel spherical joints make life uncomfortable. They also tend to wear and are not really the best option for a street car. The hard rubber bushes are not any rougher than polyurethane, which used to be my standard choice, but poly has its own issues.

You will note that I am being hypocritical here. The GKTech FUCAs have 3(!) spherical joints on each (in fact, they actually have 5 because there's another pair inside the big end). I have had trouble with these wearing on my car, but as it turns out, not as much trouble as I thought. That's a whole other issue. Anyway, the point is that I am prepared to put up with some sphericals on my (street) car, but not prepared to put them everywhere and turn the NVH up to 11 everywhere.

2 minutes ago, GTSBoy said:

No. The steel on steel spherical joints make life uncomfortable. They also tend to wear and are not really the best option for a street car. The hard rubber bushes are not any rougher than polyurethane, which used to be my standard choice, but poly has its own issues.

You will note that I am being hypocritical here. The GKTech FUCAs have 3(!) spherical joints on each (in fact, they actually have 5 because there's another pair inside the big end). I have had trouble with these wearing on my car, but as it turns out, not as much trouble as I thought. That's a whole other issue. Anyway, the point is that I am prepared to put up with some sphericals on my (street) car, but not prepared to put them everywhere and turn the NVH up to 11 everywhere.

I just wanna keep my current set up while being reliable and not wear through tires every year. Looking at the back you can tell it has the smallest bit of camber, my guess from the coilovers, it’s a very nice look to it while allowing me to be as low as I am. 

You want -0.75° to -1° at the rear. More than that will lead to rapid wear on a street car. At the front, up to 2°, but better at 1.5°. I have been running slightly more camber in the last year than previous, and I can see the wear difference on the inner edges - very clearly.

It's a road driven R32 that has stock arms, just run -0.5 degrees of camber each side. The slightest amount of power and the arse end will squat and the camber will ramp to the moon and back.

Best option is to convert to a S14/15 subframe but with your power goals and tyre wear concern probably money better spent on new bushes, adjustable arms etc.

On 5/21/2019 at 11:49 PM, Dose Pipe Sutututu said:

It's a road driven R32 that has stock arms, just run -0.5 degrees of camber each side. The slightest amount of power and the arse end will squat and the camber will ramp to the moon and back.

Best option is to convert to a S14/15 subframe but with your power goals and tyre wear concern probably money better spent on new bushes, adjustable arms etc.

This is the amount of camber it has currently

67A3E5A3-170C-438E-BD44-65BF527931AB.jpeg

94FD0381-5A6A-4512-B838-1BAACFA93184.jpeg

D1E4E222-1E9E-4B2D-A6BA-CF0B30EA663E.jpeg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...