Jump to content
SAU Community

Recommended Posts

Hello, i have been searching for gearboxes for a while now and i cant really make up my mind.

The car will be street driven so the gearbox must have a reverse and be able to downshift by itself etc.

Seen some people using powerglide t400 / t700 and liberty gearboxes etc, but the liberty gearbox (clutchless) seem to be pain in the ass for roaduse?

anyony got any suggestions here? the gearbox must hold for atleast 1200 bhp

 

Best regards

Nice street car with 1200hp.. Powerglide or th400 are your only choices really.. Mate owns a 1000hp GTR and commented on the sequential being a little rough for a streeter. 

Really depends on the type of racing you plan on.. auto would be bit average for circuit, holinger would be ok for drags. mentioning liberty leads me to believe its a street drag car?

Edited by azzada1
On 20/05/2019 at 9:17 PM, azzada1 said:

Nice street car with 1200hp.. Powerglide or th400 are your only choices really.. Mate owns a 1000hp GTR and commented on the sequential being a little rough for a streeter. 

 

 

unsure what you mean by a little rough, although I am only around the 800whp mark, I find the holinger perfectly streetable, obviously using the clutch as cruising around for daily driving. 

Wow, First you wanted an OS giken or PPG synchro gearset, and now you're talking Autos ? WTF ? That's a pretty dramatic difference between setups. If you go the auto route it is basically a "street registered" drag car. C'mon if it's got an auto in a BNR32/BCNR33/BNR34 to me it is hardly a GTR anymore.....

At least the sequential dog boxes have a certain amount of "having your cake and eating it too", as they can be streeted, can be circuited and can be drag raced all with good results. I really hate the idea of an automatic GTR.

Anyway CRD have done TH400 on GTR like JUN II with 4WD so it is possible.

I think CRD and Maatouks can both supply a TH400 and the necessary gear to install the box. 

 

the actual set up of it is the tricky bit, I would only go auto if it was going to be setup by one of the guys who have runs on the board to make it all work. 

2 hours ago, hattori hanzo said:

 

unsure what you mean by a little rough, although I am only around the 800whp mark, I find the holinger perfectly streetable, obviously using the clutch as cruising around for daily driving. 

Just the usual multiplate clutch with laggy RB "roughness".. more so in comparison to an auto. Setting it up would be alittle tricky although it looks like some shops just manage to buy a combo from Als raceglides and with afew converter tweaks its running 7s/8s haha

2 hours ago, azzada1 said:

Just the usual multiplate clutch with laggy RB "roughness".. more so in comparison to an auto. Setting it up would be alittle tricky although it looks like some shops just manage to buy a combo from Als raceglides and with afew converter tweaks its running 7s/8s haha

I would suspect those guys who setup and run 7s and 8s have been playing and tweaking with converters for years. I would be cautious of thinking a newbie could replicate.  

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...