Jump to content
SAU Community

Recommended Posts

Hi guys,

i'm going to get off my stock turbo an put on a Garrett GTX3076.

Other mods like FMIC, 600 cc injectors, link g4+, DW fuelpump etc. will be or were already added.

So I took the head off and got it machined to have an even surface. I've cleaned the block with a razorblade to get off the rest of the oem headgasket. The machine shop took off 0.16 mm from the head to get an even surface. The oem gasket thickness is 1.2 mm as I've read, so if I add the 0.16 mm the replacement has to be at least 1.36 mm. Correct?

As I am from Germany, i've searched for a metal headgasket in the local online shops but just found 1.2 or 1.5 mm but no 1.4 or 1.3.

 

So which thickness would you recommend? Or would the oem Nissan gasket be good enough for my setup, keeping in mind that the block was only cleaned by hand?

Ok, thnks for the info. Is this the correct one? https://www.tj-partshop.com/products/13009-Tomei_Headgasket_Zylinderkopfdichtung_Nissan_RB25DET

It is available with 1.2 or 1.5 mm. Which thickness would be the right choice?

The Tomei compression rate calculator says that the oem gasket thckness is 1.1 mm and the compression is 8.97.

With the 1.2 mm gasket the compression rate would be 9.03 and with the 1.5 mm it would be 8.76. 

1 hour ago, GTSBoy said:

How can a thicker gasket increase compression ratio?

I've clculated the compression ratio value for the 1.2 mm including the 0.16 mm of material that the machine shop removed from the head.

When I use the 1.2 mm gasket it will be the same as 1.04 mm gasket with the cylinder head before machining it.

11 hours ago, Finn_GT-T said:

Ok, thnks for the info. Is this the correct one? https://www.tj-partshop.com/products/13009-Tomei_Headgasket_Zylinderkopfdichtung_Nissan_RB25DET

It is available with 1.2 or 1.5 mm. Which thickness would be the right choice?

get 1.2mm

It's 2019 not 1979 where we have shitty ECUs :) 

2 hours ago, AngryRB said:

Just get a stock RB25 head gasket and ARP studs.. 

 

You know a Tomei or Nitto head gasket is much more? Not to mention it's better than the stock composite head gasket.

 

1 hour ago, Dose Pipe Sutututu said:

You know a Tomei or Nitto head gasket is much more? Not to mention it's better than the stock composite head gasket.

 

I know my RB3025 has no issues at 350kw, is a simple oem RB26 gasket that was very reasonable cost from Kudos with ARP studs.. 

If the block surface isnt perfect then it could leak and after pulling engines out a few times recently im over that bullshit so id advice OP to keep it simple.

 

1 minute ago, AngryRB said:

I know my RB3025 has no issues at 350kw, is a simple oem RB26 gasket that was very reasonable cost from Kudos with ARP studs.. 

If the block surface isnt perfect then it could leak and after pulling engines out a few times recently im over that bullshit so id advice OP to keep it simple.

 

You clearly missed what I said earlier about Tomei or Nitto head gaskets ?

How I see it is you've spent that money/time to take off the head and skim it, purchased a larger turbo and going to run ARP studs (over the factory head bolts), then what's an extra $200 to the equation? not much.

Not to mention the Nitto OR Tomei headgasket will seal better and also will withstand the punishment as it's o-ringed. Every car workshop does the same thing. I also got told this advice from both MRC and Billtech (both reputable RB workshops).

I would only advise going with a Cometic or similar style headgasket if your block is prepped.

12 minutes ago, GTSBoy said:

Or perhaps the correct grammar version where you advise against it?

FUUARK - this is proof Asian Males cannot multitask, was typing out an e-mail to a vendor at the same time about "advising" shit too LOLOLOL

(have edited the previous failed post)

Thanks @GTSBoy

 

Thank you all for the replies. This forum is much better than the german equivalent.

ARP studs are already in my garage waiting for me to screw them into the block. I think I'll go for the tomei gasket because of the small extra cost but higher (presumed) reliability compared to the oem gasket.

Will the higher compression ratio be an issue when mapping the link ecu because of the risk of knocking? Keeping in mind that the stock knocksensors will stay in the block.

By the way, what do you think about applying permatex spay gasket to the tomei gasket before assembly? Does it help to get a better sealing, or is it just wasted money?

Edited by Finn_GT-T

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for all the replies fellas. Gonna finish putting it back together and see how it handles the set up. If it starts pinging it’ll be parked.
    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
×
×
  • Create New...