Jump to content
SAU Community

Recommended Posts

What are some control arm choices for R34 GTR ? I have Cusco Front and Rear Adjustable Control Arms now, and the front ones are busted. I would like to use this chance to replace everything, since Im building my engine as well. I don't drag race my R34 , only occasional track days and mostly aggressive mountain runs. Seems like not every brand makes a complete kit of control arms ... so any suggestions?

I'm looking at:

  1. RaceFab
  2. Ikeya Formula
  3. Nismo
  4. GKTech
  5. Voodoo13

 

Edited by etang789
Link to comment
https://www.sau.com.au/forums/topic/479356-control-arm-choices-for-r34-gtr/
Share on other sites

  • 2 weeks later...
On 16/12/2019 at 3:20 PM, BK said:

The 33 and 34 GTR arms are the same, and on my 33 I have Ikeya Formula arms front and back for over 12 years. Expensive but very good.

Correction. Been That long only just realised my rear upper control arms are JIC C304780. Same thing goes though, JIC is equally as good as Ikea. Ikeya formula. Whiteline seems to have the equally good equivalent too for the rear. The front though Ikeya hands down.

image.png.6b89d24ea1717cca100e7603234d7cd6.png

Here is the Ikeya fronts I'm using:

image.png.6dbb421cb29041656d11960ca71b6332.png

  • 1 month later...
On 12/28/2019 at 8:49 PM, BK said:

Correction. Been That long only just realised my rear upper control arms are JIC C304780. Same thing goes though, JIC is equally as good as Ikea. Ikeya formula. Whiteline seems to have the equally good equivalent too for the rear. The front though Ikeya hands down.

image.png.6b89d24ea1717cca100e7603234d7cd6.png

Here is the Ikeya fronts I'm using:

image.png.6dbb421cb29041656d11960ca71b6332.png

Thanks for the reply. No noise?

What are the difference between the one you are using and this one?

 

image.png.e4ba080654d1ba7ef0625a9b876bc052.png

http://www.ikeya-f.co.jp/article/15016132.html

BK's do the adjustment with two plates that are slotted and so can slide in-out relative to each other, and use bolts through them to lock them together.

The bottom ones are the same as everybody else's. Just relies on big threaded rods and locknuts.

The bottom ones need to be adjusted carefully so that the same length change is made on both the front and rear half of the arm. The top ones are more guaranteed of correctly adjusting both halves, seeing as they are not halves! But a few people harbour worries about the types of arms that have sliding plates that lock together with through bolts as they fear they will shake loose. May or may not be founded fears.

The top ones are also spherical jointed on the upper inners and I don't think the new ones are.

Not really any noise I can detect in them but they are spherical so tightens everything right up. Regarding the top moving plates, they have a fine saw tooth design between them so they are adjusted in like 2 or 3 mm increments and lock plates together so they can't slip. The bolts would all have to substantially come loose for it to move, which has never happened in the time I've used them.

The inners pillow ball rods are also length adjustable too. I actually have Whiteline offset camber bushes in the outer too with these, so you end up getting 3 different points of camber adjustment on the front to get absolutely even length arms and spot on camber. (Completely overkill and not needed as you can start chasing your tail if you aren't up with what you're doing)

Wish there was something like this for the 32

How/where did your Cusco front arms break? And you are talking about upper, not lower? They are one of the most solid designs i've seen; adjustment is a bit limited but you can modify to get a 4th setting easy enough.

I have used those 2-piece ones with no issues, but they are only joined by the centre bolt which i wasn't a fan of. Much prefer a bracketed 1-piece arm.

  • 4 weeks later...
On 3/5/2020 at 3:35 PM, hardsteppa said:

How/where did your Cusco front arms break? And you are talking about upper, not lower? They are one of the most solid designs i've seen; adjustment is a bit limited but you can modify to get a 4th setting easy enough.

I have used those 2-piece ones with no issues, but they are only joined by the centre bolt which i wasn't a fan of. Much prefer a bracketed 1-piece arm.

so I may have to go with GKTech for the 1-piece front upper arm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...