Jump to content
SAU Community

Recommended Posts

If it’s been wired to 12v will that have f**ked the sensor?

as I’ve tried changing the wiring to suit as per above, so wired black to yellow and white to green. 
or have I messed that up (I’m terrible with wiring it’s my number one hate 🤣)

2 minutes ago, DaymoR32 said:

If it’s been wired to 12v will that have f**ked the sensor?

Hmmmm not sure, but an assumption is maybe.

A reluctor creates its own voltage so you don't feed it one.

1 minute ago, Dose Pipe Sutututu said:

Hmmmm not sure, but an assumption is maybe.

A reluctor creates its own voltage so you don't feed it one.

Aye probably dead then 🤣 will probably just pop the stock CAS back on.

i do have the paper wiring diagram with notes on it somewhere so I’ll cross reference that first

26 minutes ago, DaymoR32 said:

Aye probably dead then 🤣 will probably just pop the stock CAS back on.

i do have the paper wiring diagram with notes on it somewhere so I’ll cross reference that first

Maybe find the spec sheet and see what the resistance of the coil is, possibly it's not fried? Especially if you didn't short it 

15 hours ago, Dose Pipe Sutututu said:

Maybe find the spec sheet and see what the resistance of the coil is, possibly it's not fried? Especially if you didn't short it 

maybe another thing for me to try? timestamped (i know its the nz wiring kit, but this is on the haltech software side)

 

12 minutes ago, DaymoR32 said:

maybe another thing for me to try? timestamped (i know its the nz wiring kit, but this is on the haltech software side)

 

You can just swap the pins at the CAS connector side.

You could go old school and use a test light to see which pin is going back to B1 on your ECU

On 4/19/2024 at 10:45 AM, Dose Pipe Sutututu said:

You can just swap the pins at the CAS connector side.

You could go old school and use a test light to see which pin is going back to B1 on your ECU

I ended up trying every pin combination. got the car to start once, then rev'd it and it died. then couldnt get it started again.

Threw my toys out the pram and put the stock CAS on and it fired first turn of the key (with backup map reapplied)

I'll re-visit it another day when i get the motivation again.

40 minutes ago, DaymoR32 said:

I ended up trying every pin combination. got the car to start once, then rev'd it and it died. then couldnt get it started again.

sounds like you are super close, either the air gap is out OR the trigger arming voltage is too high.

In NSP, just plot the trigger voltage vs. RPM vs. time and when you crank it you'll see what it reaching, adjust the trigger arming to suit

27 minutes ago, Dose Pipe Sutututu said:

sounds like you are super close, either the air gap is out OR the trigger arming voltage is too high.

In NSP, just plot the trigger voltage vs. RPM vs. time and when you crank it you'll see what it reaching, adjust the trigger arming to suit

next time i have a full weekend i'll have another play, currently one month away from wedding so have no free time...

Thanks for the pointers though,

1 minute ago, Dose Pipe Sutututu said:

Don't buy a Tiguan :D 

I'm from the UK, everyone knows you buy a Seat or a Skoda as they generally run better than their VW / Audi Brothers 😆

  • Haha 1
4 minutes ago, DaymoR32 said:

I'm from the UK, everyone knows you buy a Seat or a Skoda as they generally run better than their VW / Audi Brothers 😆

Lololol... Funny between brands reliability changes, yet it's technically the same parts.

  • 10 months later...
55 minutes ago, shortyboy said:

any update on the yelsha-d trigger setup? Looking to get one for my neo on link g4x

No sorry mate, I gave up on it, also sold the car mid December and recently replaced it with a BYD Shark / Temu Raptor

IMG_1092.thumb.jpeg.559cf3aa3da79d60352975f114eb3f07.jpeg

IMG_1093.thumb.jpeg.ef526009f8953da4949c1f8418afaea0.jpeg

  • Like 1
22 minutes ago, DaymoR32 said:

No sorry mate, I gave up on it, also sold the car mid December and recently replaced it with a BYD Shark / Temu Raptor

IMG_1092.thumb.jpeg.559cf3aa3da79d60352975f114eb3f07.jpeg

IMG_1093.thumb.jpeg.ef526009f8953da4949c1f8418afaea0.jpeg

Aye I know, moving interstate, have to give up the work vehicle so replaced it with something “sensible”. Fastest Ute you can buy for under 250k 🤣

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...