Jump to content
SAU Community

Recommended Posts

G’morning my skyline R33 turbo,manual won’t start when cold. It will fire eventually but won’t continue to run.Starts first time when hot.I have changed spark plugs & coils. Any information would be greatly appreciated.Thanks Robbert.

Link to comment
https://www.sau.com.au/forums/topic/480108-skyline-cold-start-problems/
Share on other sites

Do you have a strong battery with good connections? Another possibility is the temp sensor for the ecu. It is the one with two terminals ..the one with a single terminal is for your dash gauge. Unplug the ecu terminal and if the car starts better then that one needs to be replaced.

8 hours ago, KiwiRS4T said:

Do you have a strong battery with good connections? Another possibility is the temp sensor for the ecu. It is the one with two terminals ..the one with a single terminal is for your dash gauge. Unplug the ecu terminal and if the car starts better then that one needs to be replaced.

 

47 minutes ago, Nortyone said:

Yes brand new battery and terminals clean as a whistle. Could you please give me more info where ECU is .thx.

 

47 minutes ago, Nortyone said:

Yes brand new battery and terminals clean as a whistle. Could you please give me more info where ECU is .thx.

ECU is in the LHS kick panel but you don't need to access it - disconnect the sensor at the sensor: follow the top hose to the block and you will find two sensors - just pull the plug off the one with two wires.

  • 4 weeks later...
20 hours ago, GDZ32 said:

Is the car on E85? common problem with E85 cars. Just keep cranking lol

Common with a lazy tuner :)

Mine starts in any temperature 1st go, and idles fine.. just doesn't drive very well for the 1st minute haha

25 minutes ago, Dose Pipe Sutututu said:

Mine starts in any temperature 1st go, and idles fine

Out of interest, how often do you start / drive it? Does it sit for weeks/months, then still start first go?

Have an R33 GTST track car with lots of mods, including E85. It starts fine when cold if it's run regularly, but if it sits for a while (> a month) it's very hard to start - crank until battery goes flat, recharge & try again....

31 minutes ago, GeeDog said:

Out of interest, how often do you start / drive it? Does it sit for weeks/months, then still start first go?

Have an R33 GTST track car with lots of mods, including E85. It starts fine when cold if it's run regularly, but if it sits for a while (> a month) it's very hard to start - crank until battery goes flat, recharge & try again....

Probably once every 2 weeks and yes it just sits around in my back yard. Last time I drove it was at the Sparesbox skid pan (performed terribly, never take a track car to a skid pan, it doesn't skid very well)

E85 is fun, there's a fine line between wetting the plugs and not starting and not enough cranking fuel to get it started. Then there's all the other dimensions of intake air temp, ethanol concentration, etc. I find adding a good amount to the initial prime table makes all the difference. Happy to send you my kebabtech tune file for R&D if you like.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...