Jump to content
SAU Community

Recommended Posts

One big thing people leave out about e85 is the amount of fuel you use vs pump. I have done research and talked to people and for a street driven car to and from work and the shops it was way out. I get flex fuel and running a pump tune and a e85tune.

im still running 1000cc injectors, Steve thinks they will be done with water meth. I know for that 1000hp number e85 will most likely have to be used to get the bang going 

On 21/06/2022 at 11:04 AM, WR33KD said:

One big thing people leave out about e85 is the amount of fuel you use vs pump. I have done research and talked to people and for a street driven car to and from work and the shops it was way out. I get flex fuel and running a pump tune and a e85tune.

im still running 1000cc injectors, Steve thinks they will be done with water meth. I know for that 1000hp number e85 will most likely have to be used to get the bang going 

Yep this is 100% accurate, you'd not want to run E85 to and from work.  The extra volume of fuel you need with ethanol goes up steadily as the blend increases, and that extra fuel usage impacts "just cruising" as well.   You definitely need a big fuel system if you want to make 550+kw on E85, though really if you want 550kw+ then you're probably a bit in denial if you think you can cut costs at this stage.   Block strength is potentially coming into question, OEM Nissan gearboxes are at the end of their line, the whole build has to be pretty serious at this stage.  Going a big fuel system when planning for 700whp+ on a smaller RB is pretty incidental in the grand scheme.

This still brings back the "but run flex fuel" thing, if you are aiming at commuting etc you probably don't want/shouldn't have methanol just sitting around in the car waiting for you to thrash it.  There is the clear bonus that you don't use it when you're just driving it normally, but then also you don't want it to get contaminated over time or even lose track of the level.  It's an extra thing you need to keep an eye on... the flex fuel idea again is one where you only put ethanol in if you want to get up to no good.  By E30 you have really good gains and the impact on fuel economy isn't actually that nasty by that point, if you want to get real fancy for an event then you can try and get it up to E50+ but you don't need to measure or think about it.

After that, keep putting normal pump gas in it and it'll gradually dilute itself down to E10 or less as you top up with pump gas and the tune will dial itself down to suit.   If you have a build that is going to make 550+kw on E85 then it's not going to be gutless on a pump gas friendly tune, and with flex you don't need to keep topping up the WMI, you don't need to do anything special.  Just drive the car and the tune will make sure everything is safe and well.    That's the kind of reasoning we've used at least :)

But yeah "for now" I'm sure if you can do the 550kw power level with pump and WMI and the 1000s  then it's at least a good stepping stone.  

 

Gearbox, drive shaft and axles have already been swapped out for bigger and better items. 
This tune is just that another stepping stone to the main goal. I’m not one to go all in at 1000hp and crash the thing. With each upgrade I need to re learn and get used to how the car feels. Once this step in done the final step will most likely be e85 and a full re work of the fueling system. Baby steps to get used to the power

  • Like 1
On 21/06/2022 at 1:45 PM, WR33KD said:

Gearbox, drive shaft and axles have already been swapped out for bigger and better items. 
This tune is just that another stepping stone to the main goal. I’m not one to go all in at 1000hp and crash the thing. With each upgrade I need to re learn and get used to how the car feels. Once this step in done the final step will most likely be e85 and a full re work of the fueling system. Baby steps to get used to the power

Sounds like a solid plan :)  Its going to be a monster as is.

  • 3 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...