Jump to content
SAU Community

Recommended Posts

6 minutes ago, drifter17a said:

Mine is gtt r34 with 500 bhp looking to boost up to 650 as it is forge so think having heavy might not be that bad at the end due to power.

 

just worried it won’t shift in cold morning

It's not just the horsepower figure, it's the torque and drivetrain. You may be able to get away with lightweight, try it first and see if it grinds at all.

47 minutes ago, joshuaho96 said:

If the synchros are on the way out some lightweight shockproof will help but only delay the inevitable. Don't shift quickly, double-clutch your downshifts. You will be able to get a bit more out of the transmission before rebuild. Don't try to DIY a transmission rebuild unless you feel like taking the transmission out multiple times. You will save a lot of money if you're willing and able to drop the transmission yourself, that's a good chunk of change right there.

It's been 8 years now, ~80000km, and no change in shift quality on my box from the first time it managed to change gears with smurf's blood in it.

26 minutes ago, drifter17a said:

i take it your box was worn so it won't shift and redline brought it back ?

Yes. I bought it for Neo my engine conversion and it changed gears nicely when not spinning, but would not while the engine ran. Changed to lightweight and it would change gears straight away.

26 minutes ago, drifter17a said:

new refurb one is around £1300 and want to kill this, buy one next year and then swap.

I can never understand the "kill this" mentality. I bet you I could happily drive your gearbox for the next 10 years.

  • 2 weeks later...
  • 4 years later...

I have a 32 GTR and recently had the standard 5 speed rebuilt with R33 s2 syncros and have this exact same problem! Gearbox shifts fine when not under load but doesn’t matter what gear I am in and if I try and change gears under power then it always misses the next gear and the pedal goes to the floor… I have a cube short shifter on it as well and have the recommended redline MT90 and Nulon smooth shift so not sure what’s going on..? 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...