Jump to content
SAU Community

Recommended Posts

Hi guys,

Just a quick question, my engine is at the shop currently being rebuild.

I know the engine currently has ARP2000 head studs installed (for around 3 years and not driven too hard). 

My engine builder suggested ARP CA625+ head studs. I know they are stronger, however they are also 3x the cost of ARP2000.

Question - Do I need ARP CA625+ ?

I have intentions installing a gtx3582r or 84rs or a g series equivalent turbo later on. It will be a street car. 

Another question - I know the ARP2000 head studs are reusable, however, is it completely safe to 'reuse' them? or would it be safer to just install fresh new head studs? 

Thanks in advance everyone!

 

 

 

 

 

 

How much boost/power you planning on?

Also they are "reusable" but I personally wouldn't. Sell them to someone that's doing a simple build or a refresh on their motor and get new studs.

 

As above, custom age is great if you've got money to burn and are aiming for 500rwkw+. I used them on my 32, but meh.

Do you need it, probably not as 2000s will be adequate.

That's a really good question, I really don't know.

I'm not really aiming for power, more wanting response. Maybe 400 rwkw more or less? Just whatever the engine is happy with, with the set up I described. I love the watching the mines r34 gtr on youtube. If I can get something like that.. or better! That would be awesome! (Hopefully single gtx or g series turbos are better than old twins they had on).

I'm leaning towards arp2000 simply because of cost. 

I am not looking for 500+ rwkw that's for sure.

 

 

4 minutes ago, sr20dettttt said:

Nice arp2000 it is then. Thanks guys!

Nope I don't know the specs it was torqued to prior as a mechanic did it for me. But I would assume, since he is a mechanic, they would follow correct torque procedure? 

 

 

 

 

Well it's not black and white, if you torque it to ARP specs, then they will be below their yield point and the metal will 'spring back' and be reusable again. This is not a guarantee that they are as good as new, but typically they are fine to be used again. 

You can torque ARP studs to yield, it will clamp the head down tighter but now the studs are a one time use only. This isn't wrong, the mechanic may have a valid reason for wanting a higher clamp on the head.

Without knowing how much torque has been put through them, I wouldn't risk using them again. 

  • Like 4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...