Jump to content
SAU Community

Strongest sequential and why?

khezz
 Share

Recommended Posts

khezz Rising Star

khezz

Posted
Posted

With RBs pushing power further and further past 1000hp the demand on a gearbox is ever greater. 10 years ago a 1000hp transmission would be considered unbreakable. Now, with the cost of power parts going down and quality going up, the same person who could afford a sequential 10 years ago would be aiming for a number far higher then 1000hp. Keeping the cost aside and keeping dedicated drag boxes out of it (would love to see a thread on Liberty and Jericho transmissions)

Are transmission manufacturers keeping up?

What is the strongest sequential out there?

Why do you think/know so?

I am leaning towards the Hollinger. Been around for a very long time, very widely used in motorsports. Seems to be the only one with straight cut gears which eliminates sideload.

Link to comment
https://www.sau.com.au/forums/topic/481213-strongest-sequential-and-why/
Share on other sites
Old man 32 GTR Proficient

Old man 32 GTR

Posted
Posted

The Holinger sequential for GTR uses helical cut gears, as does PPG and OS 88. Samsonas and Albins use straight cut 

I think most would agree Albins would be top of the food chain 

Predator1 Rising Star

Predator1

Posted
Posted

You're right, back in the day, most of the GTR's though were either 2.6, or 2.8 only. RB30's werent THAT common.

I was in this exact boat when planning for a gearbox. I went with a 3.2 route. I sussed out all my options and talked to a tonne of people around what options there were for GTR's(excluding auto's here):

* Getrag 6 speed
* Gearset
* Sequential

Personally, I wanted peace of mind hence why I didnt go for a gearset or 6 speed. I mean, by the time you've done either of those 2 options you wouldn't get much change from 15K right? Plus, I dont know how long they would last with the fat torque of the 3.2...I also scoped out the sequentials out there, and in the end I went with the Albins as to me it seemed like the pick of the crop(Not saying the other Seq manufactures are shit, but its just my opinion). Plus, the Albins kit literally comes with everything minus the clutch.. no faffing around looking for tailshafts/transfer cases etc.

 

hattori hanzo Community Regular

hattori hanzo

Posted
Posted

I have a Holinger and love it, I bought it a few years about now circa 2015

 

however Albins and Samsona's seem to be the pick of the bunch these days.

 

Particularly now the albins can slot straight in without panel beating and the adjuster gear to tweak ratio's is very convenient and samsonas seems to put up with the beatings

BK Grand Master

BK

Posted
Posted
23 hours ago, Old man 32 GTR said:

Holinger sequential for GTR uses helical cut gears

I was under the impression you could get either, as the Holinger GRA-6N box for the group A R32 cars were straight cut, and was essentially the same ?

Anyway I would echo above - Albins all the way. Compared to Samsonas they have definitely more all round Motorsport proven track record within Australia and are completely Australian. In off road like 800hp+ buggies with monster torque that race here in the NT Finke desert race, there is basically only one manual box used that wins.

Albins

Old man 32 GTR Proficient

Old man 32 GTR

Posted
Posted

I called them not that long ago to ask a few questions about their sequential, they never mentioned anything about the option for straight cut? But I didn’t ask either, but the standard sequential design is helical cut. 

BK Grand Master

BK

Posted
Posted

Standard option looks like it, as the pictures in Holinger GTR workshop manual are all showing helical gears on the disassembly except reverse. Main and counter shafts are both splined on gear so they definitely can do it. The earlier GTR boxes the Hollinger GRA-6N and HKS-GTR were only straight cut.

2012 GTR MANUAL.pdf

IMACUL8 Veteran

IMACUL8

Posted
Posted (edited)

Same experience as Moray - when I spoke to Holinger couple months ago - helical only.  Not sure why that is now - as I'm sure you could get them in straight cut years ago.

I went with the new Albins ST6-LP - i believe its the only one with a internal oil pump.!

 

14 hours ago, Old man 32 GTR said:

I called them not that long ago to ask a few questions about their sequential, they never mentioned anything about the option for straight cut? But I didn’t ask either, but the standard sequential design is helical cut. 

 

Edited by IMACUL8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...