Jump to content
SAU Community

Recommended Posts

Hey all, so from what I've read in old posts I'm pretty confident I blew one or both of the stock turbo exhaust wheels last night. Car was on boost at WOT, then I shifted (around 6500/7000) heard a loud noise car juddered and rattled and no more boost. What I wasn't able to find searching and has me worried were some of the other symptoms I had. I don't remember if I let off right when it happened or not, but shortly after the pop I pulled up to a red light. It made some horrible rattles noises, sounded almost like my front pipe came off, idled horribly going from too low to too high, but then rattles went away and it settled down. I didn't notice any smoke out the back but to be honest wasn't looking back there. After the engine settled down there was still a spiny rattle noise that's particularly noticeable when near the exhaust tip, idles normally, and drives normally off boost. I limped it the 2 miles home and it drove ok but couldn't build up boost. Oil pressure, oil temp, and water temp all remained normal; even when the engine was acting up. Haven't started it up since.

For reference I have a decat pipe, tomei equal length downpipes, and a cat back muffler. Rest of the car is stock. I noticed the day of that the car was making a bit more boost than usual but I never turned it up myself and had been running stock boost until then.

Planning to take off the down pipe, endo-scope up the rear of the turbos, compression test, and endo-scope through the sparkplugs for any noticeable damage. If I don't find anything doing that I'll start checking intake/intercooler piping and get the stuff for a leak-down test. Again, pretty sure this is a blown stock turbo exhaust wheel, but I'm wondering if anyone has any other ideas for what to check and if my symptoms indicate something catastrophic. Should I start budgeting for a new/rebuilt short block?

Also side question, assuming the engine isn't boned, can I run -5's on stock boost with a stock ECU/fuel system? Not sure I have the funds to do everything at once and was hoping to get it back on the road this summer.

It sure sounds like a lost turbo wheel if it idles and drives OK off boost but won't make boost. As you don't have a cat you are unlikely to ever find the missing wheel. 

Having an intercooler pipe blow off or split is another potential cause and can sound terrible, but the car almost always won't start or idle in this case.  Best to carefully check each large intake pipe before you start pulling turbos off, as well as obvious failures like pipes not being connected there can be harder to identify issues like splits under hose clamps for example.

Least likely but still possible is you've had an engine problem at the same time, eg broken ring lands. A compression test will tell you if there is a problem but again this is unlikely if it starts and idles OK.

If it is a turbo wheel coming off I have heard of engine damaging resulting but have never seen it personally. Apparently ceramic from the turbo wheel have more velocity than exhaust gases and can travel through the open exhaust valve into a cylinder, scoring it badly enough to require on oversize piston rebuild.

Thanks Duncan. Have you heard of a lost wheel causing a rough idle and sputtering for 30 seconds to a minute after it happens? That's what has me worried I may be one of the unlucky few that had ceramic backflow into the cylinder. I've also heard of the ceramic damaging the internals but wasn't sure how common it was. I have a borescope so hopefully that should be good enough to see any damage that might have been caused.

And that's a good idea, I'll check all the intercooler pipes closely. It's all original and almost 30 years old so definitely a possibility. What I could see without diving to much into it last night looked like everything was connected still at least.

Then I would go order a twin scroll single turbo manifold, a twin scroll turbo, and two gates. Don't replace shitty twins with another pair of shitty twins.

I know Americans love their "twin turbos" but seen any fast reliable Supra with twin turbos? They all go sex spec single.

When i lost my turbo wheels at WOT i just lost boost but never had splutters etc.  Although i was on the highway so didnt slow down much.

 

I did eventually have an engine failure but I did a rain launch for a laugh so i think it was just a stock pump failure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
    • Its a well known brand in New Zealand; its a rebrand of the Rhino RAV3.  I don't know what the wiring difference *is* between the rev.1 (installed about 15 years ago) and rev.2; but as you say I would think its reasonable that it uses the same immobiliser relay circuits. I had a look but couldnt see a similar harness; but didnt move things around since I didnt want to mess with it   It was one of AVS well known Authorised Installers; I spoke to AVS themselves about it but theyre unsure hence seeking advice more so from the skyline community who are more familiar with the actual car and its wiring. Im in Auckland; but the installer is on the other side of the city so hes very reluctant to come back to even look at it to confirm something isnt connected into the wrong wire.  I dont want to drop the name since they *did* do a really good job for the most part. Everything is very tidy and he fully replaced all the alarm wiring, all the sensors, the wiring to the door motors, installed a switch which was never installed in the first place...really happy with the alarm install itself..just not this one issue. We all make mistakes, if it is the alarm, I just want my fuel pump getting proper switched, fused, power as it was; without having to shell out for an auto electrician to switch a wire and tell me it was the alarm. 
    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
×
×
  • Create New...