Jump to content
SAU Community

Recommended Posts

I have a new bumper for my car in trying to prep and paint. It didn't have holes for the headlight washers but the cutout was marked on the back and I cut them both out. The problem is I probably went a little wide on one side and I'm not sure the hole will be properly covered when the washers are off.

What I'm going to do is to try and close the hole a little bit but I'm not sure what I can use to do this. I tried filler but it just wasn't strong enough. What should I use?

Thanks guys

Christian

Link to comment
https://www.sau.com.au/forums/topic/482486-best-thing-to-fill-a-bumper-hole/
Share on other sites

Obviously the most common thing when working with bumper plastics: Use fiber glass stuff from the inside, put some layers on, then fill from the other side and make a new hole. Youd still need to cover the color difference though, but surelly the cheapest way

12 hours ago, HCD Velcra said:

Obviously the most common thing when working with bumper plastics: Use fiber glass stuff from the inside, put some layers on, then fill from the other side and make a new hole. Youd still need to cover the color difference though, but surelly the cheapest way

 

Fibreglass isn't going to stick long term to a plastic bumper, even with very good mechanical key. 

 

@PranK if you want to do the job yourself, look for a plastic bumper patch kit for a 2-sided repair. Something like this: 

https://wholesalepaint.com.au/products/3m-flexible-bumper-plastic-patch-automotive-repair-kit-05888

 

Personally I prefer the kits that use a thermoplastic or aluminium mesh patch that is bonded in place with a 2k polyurethane adhesive, but these self adhesive patches work OK too - just make sure the surface is VERY clean first, which means wipe with isopropyl alcohol, then sand with 240 grit (ignore the instructions not to sand), then wipe again with the isopropyl. 

Then you can use a flexible plastic filler (Isopon is good, 3M better) like any generic body filler and fill from the back before sanding smooth. 

55 minutes ago, PranK said:

Yeh thats the stuff. It is very easy, you just need to use the right materials.

Plastic being a low surface energy and very high flexibility makes it difficult to bond to, so rigid resins like polyester or epoxy (your two typical fibreglass resins) will struggle to bond and will eventually delaminate. These plastic-specific repair products are just as easy to use (even easier in fact), but will do a good job of a permanent repair.

  • Like 1

I have also had great success using vinyl ester resins for these sort of repairs over the years.

Vinyl ester resin tends to be a little bit more flexible than polyester resins used in most fiberglass

But as Martin ( Unzipped Composites ) states prep work is very important for the best adhesion.

With ABS type plastics first washing the affected area first to get rip of dirt and grime first.

Sand area as required

Then cleaning the area down with acetone will begin to "soften" the plastic and make the surface sticky or tacky to the touch.

And then finally a wash down with styrene monomer being sure not to touch the area after the wash down to avoid contaminants on the fresh plastic surface.

This will give the very best adhesion between the plastic and vinyl ester resin on application.

So ends today science lesson !

  • Like 1
On 6/5/2021 at 10:01 PM, GTSBoy said:

Take the bumper to a crash repairer or a plastic welder (the sort that the crash repairer would use if they don't have their own guy) to stitch a little plastic into the hole and sand it back.

I do my own plastic welding, use a cheap as sh#t chinese welder off Aliexpress, I use good quality welding rods, and source patch pieces from other Nissan plastic bars. Then the repair is smoothed with flexible plastic filler available from repco. I have a collection of repaired R33 S1 and S2 and M bars which were discarded by their previous owners. I also make my own ABS filler paste, very easy and ingredients available from Bunnings.

Edited by Rusty Nuts
additional information
  • Like 1

Thats super cool @Rusty Nuts - sounds like a good DIY topic!

This front bar is the first time I've ever tried body work. I've already cut these holes too big and my prep work is terrible with paint and primer not even sticking to some parts and then theres the mess!!

Thanks guys, I'll try these 3M patches as they are probably the easiest for a simpleton like me, then I can just pack filler over the top. Then I get to prep and prime again. :(

 

4 hours ago, PLYNX said:

I have also had great success using vinyl ester resins for these sort of repairs over the years.

Vinyl ester resin tends to be a little bit more flexible than polyester resins used in most fiberglass

But as Martin ( Unzipped Composites ) states prep work is very important for the best adhesion.

With ABS type plastics first washing the affected area first to get rip of dirt and grime first.

Sand area as required

Then cleaning the area down with acetone will begin to "soften" the plastic and make the surface sticky or tacky to the touch.

And then finally a wash down with styrene monomer being sure not to touch the area after the wash down to avoid contaminants on the fresh plastic surface.

This will give the very best adhesion between the plastic and vinyl ester resin on application.

So ends today science lesson !

 

I still wouldn't consider this a permanent repair man. Vinyl esters aren't really more flexible than polyesters*. Realistically vinyl has better cross-bonding properties which is why it works better than polyester, but epoxy is even better again so if you had to choose a regular laminating resin to attempt to repair ABS with then it would be epoxy all day long. 

 

Fact remains though, ABS is a low energy plastic and is difficult to bond to. Not completely impossible like some others types of plastic, HDPE and Polypropylene are virtually impossible to bond, but still difficult enough that even an epoxy bond will only be 'moderate'. You can improve it slightly by increasing the surface energy of the ABS through flame treatment, though this is more difficult than just waving a butane torch around for a few minutes. There is a precise moment when the flame treatment increases the open sites on the ABS and it becomes bondable, but take it too far and those open sites break down again and the surface actually becomes 'greasy' and even more difficult to bond to. So really to do it properly requires proper equipment, and is a bit beyond the realms of repairing a vehicle panel.

 

*they are, but you're talking ~5% elongation of vinyl vs 3.5% elongation of polyester - ABS is around 50%. This can be part of the problem, because the laminated fibreglass patch will fail long before the ABS does, meaning any patch will always delaminate without much strain. Obviously this is only really an issue if the patch is in an area where the ABS is constantly moving around (try to patch an ABS mudguard and see how long it lasts), on a component that is rigidly mounted and doesn't move much like a front bumper, then the patch will mostly stay in place unless it experiences a large degree of flex at some point (like pulling the bumper off). Trouble is, on a vehicle all panels are subject to vibration, which can start to break the bond and make the repair visible underneath your paint job. It may not actually fall off completely, but it is less than ideal to have a repair showing up later once you've gone through all that effort and expense.

 

All of this is largely irrelevant simply because products exist that are more suitable for the job. 

On 6/9/2021 at 1:30 PM, PranK said:

Then I get to prep and prime again. :(

There are some good guides for prep on YouTube. Wax and grease remover use before starting any work, use before and after sanding and use a plastic etch primer if you're using cans Septone make one I've used.

Just now, Rusty Nuts said:

There are some good guides for prep on YouTube. Wax and grease remover use before starting any work, use before and after sanding and use a plastic etch primer if you're using cans Septone make one I've used.

 

Also wash with soap and water. Wax and grease remover will remove oil based contamination but not water based. Best to use both.

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...