Jump to content
SAU Community

Recommended Posts

Ok so I'm trying to take off the harmonic balancer off my RB30. I've removed the center bolt and attached the pulley tool. But everytime I go to rotate the tool, the balancer moves.

 

I have the drive belts on to try hold the harmonic balancer still but that hasn't worked and I don't have an assistant to try counteract the force being applied to the pulley.

 

 

Does anyone have any advice for me😁

Link to comment
https://www.sau.com.au/forums/topic/483241-rb30/
Share on other sites

Can you put up a pic of your setup? I don't understand why the balancer should turn due to a puller (normally the pushing rod for the balancer has a cap that rotates freely on the shaft)

Either way, even if you don't have an assistant (and assuming you don't have a flywheel lock tool) you just need a bolt on the rear of the motor, a pry bar between the bolt and the flywheel ring gear, and a long arm...

Link to comment
https://www.sau.com.au/forums/topic/483241-rb30/#findComment-7960265
Share on other sites

IMG_20220125_174037981_HDR.thumb.jpg.e41d0d48633e09dc94ca67febb80447c.jpg

I did have all belts on but I started taking them off

 

Ok so I'm trying to take off the harmonic balancer off my RB30. I've removed the center bolt and attached the pulley tool. But everytime I go to rotate the tool, the balancer moves.

 

I have the drive belts on to try hold the harmonic balancer still but that hasn't worked and I don't have an assistant to try counteract the force being applied to the pulley.

 

 

Does anyone have any advice for me😁

Link to comment
https://www.sau.com.au/forums/topic/483241-rb30/#findComment-7960268
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...