Jump to content
SAU Community

Recommended Posts

On the track (as in a circuit not a 400 straight line) I've seen my fuel temps go above 65 degrees after 10 laps of Wakefield.

Day to day driving around town probably 30s to 40s, mind you I run PWM so both pumps in the surge are duty cycled. The DW200 lift pump however is just on factory wiring with the resistor deleted.

And no your fuel temp isn't that high.

Not high at all. In the NT until I staged my two 400lph AEM external pumps with twin -8 feeds from surge with AEM 340lph in tank pump I was seeing 70 - 75 on the highway, ambients were above 40 though. After staging the 400s the temps came down under 50.

On the other 32 with PWM we had similar reduction in temp as Johnny suggested on a single Walbro 525lph pump.

  • Like 1
On 3/28/2022 at 9:23 AM, Predator1 said:

Thinking of adding the Setrab fan assisted cooler.

I wouldn't bother unless;

  • You're having fuel temp related problems that you didn't mention, or
  • You're going to change the way that you use the car that could/would lead to heat either increasing or being more of an issue, or
  • You like introducing more points of failure.
  • Like 1

I would not stage the pumps and duty cycle them together and ramp them up based on MAP (as the load axis).

At 100hz, the Walbro 450/460s don't like any duty under 40% they start to make an awful hum, however any higher they seem ok!

I suspect your pumps wouldn't be too far off that.

Part of the problem you have is 1x pump is always at full filt _ your lift pump. They're heating up your fuel unnecessarily. 

 

Also, if you have proper injector data and fuel data i.e. fuel temp vs fuel density vs. ethanol then there's no real issue with warm fuel.

This is how I've done mine (note must tuning shops will not do this, as customers don't pay them enough for their time - Link and MoTec have this predefined).

image.thumb.png.1907e8fa6b99748a9fc2f07c6edd00d7.png

On 28/03/2022 at 12:47 PM, Dose Pipe Sutututu said:

I would not stage the pumps and duty cycle them together and ramp them up based on MAP (as the load axis).

At 100hz, the Walbro 450/460s don't like any duty under 40% they start to make an awful hum, however any higher they seem ok!

I suspect your pumps wouldn't be too far off that.

Part of the problem you have is 1x pump is always at full filt _ your lift pump. They're heating up your fuel unnecessarily. 

 

Also, if you have proper injector data and fuel data i.e. fuel temp vs fuel density vs. ethanol then there's no real issue with warm fuel.

This is how I've done mine (note must tuning shops will not do this, as customers don't pay them enough for their time - Link and MoTec have this predefined).

image.thumb.png.1907e8fa6b99748a9fc2f07c6edd00d7.png

I used your fuel density table you sent me and put it in the Elite before Simon tuned it at Morpowa last year, very handy 👍

  • Like 1
On 28/03/2022 at 2:23 PM, BK said:

I used your fuel density table you sent me and put it in the Elite before Simon tuned it at Morpowa last year, very handy 👍

no more silly AFR hunting at idle, regardless of fuel temp or big injectors :) 

Haltech is great, provided it's used properly.

400902463_FPSetup.thumb.PNG.dab39a5be7e6b07d86d35f35dda0a9c0.PNG14233463_FPDuty.thumb.PNG.239b18e14e711d2820d01921307e2cd9.PNG

 

Funny you mentioned the hum noise, cos mine makes that too. I noticed in the logs stats, from memory my max Inj DC is around 38%.. So judging by that, my FP's sitting under 70%?? I think with PWM its the opposite?

What's your PWM setup?

 

On 28/03/2022 at 4:17 PM, Dose Pipe Sutututu said:

I would not stage the pumps and duty cycle them together and ramp them up based on MAP (as the load axis).

At 100hz, the Walbro 450/460s don't like any duty under 40% they start to make an awful hum, however any higher they seem ok!

I suspect your pumps wouldn't be too far off that.

Part of the problem you have is 1x pump is always at full filt _ your lift pump. They're heating up your fuel unnecessarily. 

 

Also, if you have proper injector data and fuel data i.e. fuel temp vs fuel density vs. ethanol then there's no real issue with warm fuel.

This is how I've done mine (note must tuning shops will not do this, as customers don't pay them enough for their time - Link and MoTec have this predefined).

image.thumb.png.1907e8fa6b99748a9fc2f07c6edd00d7.png

 

On 28/03/2022 at 5:30 PM, Dose Pipe Sutututu said:

ooo I lied, I run it at 200hz

image.thumb.png.28d48641d64f99dde2fbb0f277e4f30a.png

 

It's 100AMP Jaycar SSR, with flyback diodes on each Walbro 450L

Ah yeah so mines at 250hz, doubt that be an issue. The tuner didnt stick flybacks on my SSR which I always was a bit dubious about. I run the 100A SSR too. 

On 28/03/2022 at 3:38 PM, Predator1 said:

The tuner didnt stick flybacks on my SSR which I always was a bit dubious about

You need flyback diodes, if not your SSRs would be ripping hot and will fail with time.

On 28/03/2022 at 2:10 PM, Dose Pipe Sutututu said:

Look at us, all so modern :) 

Love it - running all pumps full tilt all the time is stupid!

I'd like to PWM the blue 32 with the twin 400 pumps, but can't be stuffed so it will stay staged. It works perfectly and probably draws less current than PWMing 2 pumps simultaneously. PWM on the primary external and keep the secondary staged if I can be bothered would be the go.

For Predator1 - absolutely use a flyback diode as above. I like the 1N5404 at 400v / 3A for a bit of overkill.

  • Like 1
On 28/03/2022 at 2:26 PM, Predator1 said:

Thanks guys. I'm just concerned about my tune. 

So safe to just stick 1 flyback across the SSR terminals that go towards my pumps? I think both pumps get their positive from the SSR. I'll have to double check.

The best place for a flyback diode is at the load, so across the pump terminals ideally.

.IMG_20210626_115220_0.thumb.jpg.4b9eaa7b756269c3b7d8cf71b3c8eb65.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
    • Cats are called Bella, and Donna...  Like that poisonous plant And I remember your 2 monsters, I remember making a little bit of wee when you let them out... LOL I have already installed cat doors into the laundry where their kitty litter is, and the sun room, apart from the cat doors there's not going to be any permanent mounted stuff on the interior walls (interior doors are cheap and easy to replace) I will get a outdoor cat cage thingie once I finish the landscaping out back... https://catnip.com.au/ The only off limit areas are the main bedroom and the gym room....but, currently the cats are curled up in bed, in the main bedroom with the Mrs.....LOL, the off limits for the kittens to the main bedroom lasted about 5 minutes with Jackie I currently only have 1 free standing huge cat tree multiple level scratching post thingie in the lounge room, but, I will be getting another one soon now that I'm happy with the furniture layout in the back room and have a perfect spot for it  
    • All of this is making it seem clear that running the Coppermix twin was definitely the way to go, especially in hindsight with how insane tariffs have gotten and the strength of the USD vs yen at the time.
    • That sounds like no chance of even importing one for road registering then Now I see why Duncan wants to check LHD rules for Targa...   I wonder how "bolt in" the AWD would be if you got one imported from the US and swapped it to an AUD one
    • Not to mention they drive like a bucket of bolts! yuck!
×
×
  • Create New...