Jump to content
SAU Community

Recommended Posts

Has anybody looked into obtaining a front cut V37 Red sedan from japan as a way to twin turbo a V36 (sedan)?  I figure this could be made street legal by putting it over the pits as the VR30DETT block and trans should mostly drop in with just a few hiccups (the USA has sorted now). The left over V36 motor and trans could be sold off to reduce costs also.

Anybody considered this ? 

The aftermarket route is expensive (like 25K) so the front cut would have to be cheaper (15K?). Who would undertake this in QLD... East Coast Customs ?

Pete

 

 

Edited by mybrains
Link to comment
https://www.sau.com.au/forums/topic/483985-v37-front-cut-into-a-v36-as-a-swap/
Share on other sites

So a vr30ddtt??
Yes looked into it. Waiting to see how the new Z goes first.
Its been done a heap in the USA heaps, wiring is not to hard. Definitely budget well over 25k for a shop to do everything. Allow for small things like hoses, clamps, exhaust, bigger heat exchanger, even possible brake upgrade to meet engineering requirements. Allow something like this a few months to be done.

If wanting power its easier to attach a blower, exhaust, fuel system or one of the BTW turbo kits and retune or buy just the inifiniti 
East Coast Customs don't really do conversion stuff any more but would be able to tune it or do the above work. Boys have been flat out and I know are pretty much booked for the rest of the year.

 

thanks. this is leaning me towards just selling the v36 and buying a V37 ready to go. I need to find out if AUS is ready to import the Japanese red sedans now (2019 model). Local seems to have cut off at 2018 model (before the GTR facelift). If the import is 45K and the V36 sells for 20K then its the same 25K swap over abet less hassle and easier to service etc.

Pete

Mustang V8 note is nice but turbos are easier to boot ;)

 

Local V37s have dropped alot. Some for 34K. makes swap even cheaper. Still, the 2019 model had a better electric steering system and some of the kinks worked out so I lean that way to go JDM.

https://www.carsales.com.au/cars/infiniti/sedan-bodystyle/petrol-fueltype/turbo-induction/6-cylinders/under-50000/?sort=~Price

If you go down the Q50/Q60 RS route, try to get a later model (2018) as the earlier models had issues with the turbos failing prematurely and it is $$ to replace as they are integrated into the exhaust manifold.

The RS was available with or without DAS.  Interesting, the only people that seem to hate DAS are those that have never owned one.  Unless you want to track the car and value as much steering feedback as possible, then DAS is fine.  Either the older version or newer (some on the US forums prefer Ver1)

 

Retrofitting a VR into a V36 sounds like $$$ and you end up with a unicorn that may be hard to find someone to work on it and will make it harder to sell.  Surely building and turbo charging a VQ37 will yield better results anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No need to replace the cover if it is still intact (not worn through). It would be worth checking the balancer for matching marks on the rear, but I'd assume the balancer was loose at some stage. The cam timing marks look fine, once you put the new belt on you can only be right or a full tooth out
    • Disconnecting rods! must have been an unpleasant surprise...
    • So been ocd with timing mark but checked from few angle and seems both cam are on and crank is matching as well to the slot on sump and crank pully   i noticed crankshaft cover has been robbed as per attached pic. Any ideas why? Could my balancer or harmonic be on its way out? should I replace the cover? https://ibb.co/ZR1JFYRR
    • So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
×
×
  • Create New...