Jump to content
SAU Community

Recommended Posts

Colour me confused. How can you remove the dampener to see what the idle pressure is? I feel that you are confusing the wording or the physical location of these devices. The dampeners are upstream (and perhaps on) the rail. The reg is at the outlet of the rail and is the very last physical device in the fuel system other than the return line to the tank.

Do us a favour. Locate the real, actual pressure reg. Remove the vac line from it and tell us the idling fuel pressure then.

  • Like 1
13 minutes ago, GTSBoy said:

Colour me confused. How can you remove the dampener to see what the idle pressure is? I feel that you are confusing the wording or the physical location of these devices. The dampeners are upstream (and perhaps on) the rail. The reg is at the outlet of the rail and is the very last physical device in the fuel system other than the return line to the tank.

Do us a favour. Locate the real, actual pressure reg. Remove the vac line from it and tell us the idling fuel pressure then.

Dampener is after the fuel pressure regulator on the rb26, removing the vac line changes the idling by like 0.05 bar or something like that 

If it satisfies you I also ran the car with the hose right off the fuel pressure regulator as stated and nothing changed

On 12/10/2022 at 6:54 PM, damnonrs said:

Dampener is after the fuel pressure regulator on the rb26, removing the vac line changes the idling by like 0.05 bar or something like that 

If it satisfies you I also ran the car with the hose right off the fuel pressure regulator as stated and nothing changed

The dampener would do nothing if after the regulator. What would it dampen?

 

Taking the vac line off the reg at idle MUST show an increase in pressure. That's how referenced regulators work mate. If it's not doing that it isn't working.

Or you have the vac source plumbed wrong. Can you feel a suction on the vac line when disconnected at idle?

1 minute ago, Ben C34 said:

The dampener would do nothing if after the regulator. What would it dampen?

 

Taking the vac line off the reg at idle MUST show an increase in pressure. That's how referenced regulators work mate. If it's not doing that it isn't working.

Or you have the vac source plumbed wrong. Can you feel a suction on the vac line when disconnected at idle?

Isn't the stock RB26 fuel damper in the return line? That's how I read it here:

271961703_ScreenShot2022-12-10at12_28_13AM.thumb.png.46c588e0be556871ab4b5ba08de2b778.png

7 minutes ago, damnonrs said:

Dampener is after the fuel pressure regulator on the rb26, removing the vac line changes the idling by like 0.05 bar or something like that 

If it satisfies you I also ran the car with the hose right off the fuel pressure regulator as stated and nothing changed

I agree that something is wrong if pulling the vac line only changes the fuel pressure by 0.05 bar. Look at your manifold pressure in absolute pressure. If your idle is -20 inHg then assuming your base pressure is 4 bar it should drop to 3.32 bar with the vacuum line plugged in. Are you sure your vacuum line is plugged in at the front of the balance tube? I have heard of people mixing up the charcoal canister vacuum line for the FPR vacuum line.

5 minutes ago, joshuaho96 said:

I agree that something is wrong if pulling the vac line only changes the fuel pressure by 0.05 bar. Look at your manifold pressure in absolute pressure. If your idle is -20 inHg then assuming your base pressure is 4 bar it should drop to 3.32 bar with the vacuum line plugged in. Are you sure your vacuum line is plugged in at the front of the balance tube? I have heard of people mixing up the charcoal canister vacuum line for the FPR vacuum line.

It’s plumbed like this

7805CA72-9C68-400B-80B1-84A580EAFFDC.png

2 minutes ago, joshuaho96 said:

That's the correct port, not sure why your fuel pressure is behaving weirdly then. You sure it only changed by 0.05 bar and not 0.5 bar?

I will check again tomorrow, could I have a pretty bad vacuum leak somewhere in the surge tank or something 

1 minute ago, damnonrs said:

could I have a pretty bad vacuum leak somewhere in the surge tank or something

No. Is there a strong vacuum signal on that vac line on the pressure reg when you pull it off? If there is not, suspect the source. If there is, then suspect the reg. But something is defo f**ked.

  • Like 1
4 hours ago, joshuaho96 said:

That's the correct port, not sure why your fuel pressure is behaving weirdly then. You sure it only changed by 0.05 bar and not 0.5 bar?

Change in real world is generally 3 - 4psi. 40 psi at idle full vacuum, 43psi at 0 vacuum with line pulled. Bar talk at this level is silly. 0.5bar change I would not expect realistically, that's a bit dramatic of a change at 7.5 psi and 0.05bar is basically no change.

12 hours ago, BK said:

Change in real world is generally 3 - 4psi. 40 psi at idle full vacuum, 43psi at 0 vacuum with line pulled. Bar talk at this level is silly. 0.5bar change I would not expect realistically, that's a bit dramatic of a change at 7.5 psi and 0.05bar is basically no change.

I was just going by the book value mentioned earlier. Wouldn't this depend on the particular slope/response of the fuel pressure regulator? I figure the goal at idle is to drop fuel pressure so you stay deeper in the linear regime of the injectors.

When I upgraded to a radium FPR, with the vacuum line pulled, base pressure is 43.5 psi. With the vacuum line back on, the pressure drops to 33.5 psi. 

Big difference between the stock FPR and the radium one for sure. 

21 hours ago, damnonrs said:

So I dove into the fuel system today, 

I removed the line coming out of the damper and plugged it into a fuel canister. The idling pressure dropped from 4.25 idling to 4.05 steady. I’m assuming the 5% improvement is because of all the twists and turns tk get back to the fuel tank. So damper isn’t the problem. But then I also tried plugging it straight from the regulator and it was the same thing. All that’s left to test now is regulator itself or the rail… which brings me to: do I buy a radium fuel rail with damper and fuel pressure regulator in one? Also check this out. When I rev the car the pressure just goes to 3.5 and jumps back to 4.2 I posted a video 

IMG_7513.MOV 72.15 MB · 1 download  

 

I'm not an expert on fuel systems but a 0.2 bar drop in fuel pressure just from the return lines not flowing enough sounds like a lot, especially if you haven't bypassed the FPCM. Have you bypassed the FPCM btw?

32 minutes ago, Murray_Calavera said:

When I upgraded to a radium FPR, with the vacuum line pulled, base pressure is 43.5 psi. With the vacuum line back on, the pressure drops to 33.5 psi. 

Big difference between the stock FPR and the radium one for sure. 

What size fuel lines ?

What pump ?

46 minutes ago, joshuaho96 said:

I'm not an expert on fuel systems but a 0.2 bar drop in fuel pressure just from the return lines not flowing enough sounds like a lot, especially if you haven't bypassed the FPCM. Have you bypassed the FPCM btw?

What’s a fpcm?

this is what the fuel pressure does plugging it in and out. It raises when you unplug it

 

 

38 minutes ago, Murray_Calavera said:

Lines are stock sized.

Pump is Walbro/Aeroflow/TI automotive 525 LPH.

Though so, 10psi change is not normal and sounds very restricted. What possessed you use one of these on stock lines ?!

For example our white 32 has the same 525lph with AN8 top hat fittings, AN8 supply and return lines with an FPR1200 using PWM.

Changes about 4 - 5 psi

Stock Nismo pump  stock reg on 5/16 lines changes about 3-4psi in my 33.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...