Jump to content
SAU Community

Recommended Posts

Alright, I've held off from posting this because it doesn't seem to make any sense and I know it's a topic that was beat to death and back two decades ago and then again after that.

I have an AWD 23U block from an ENR34 that was NA from the factory. I'm rebuilding it with a turbo NEO head and ARP studs to sell it on so I can move on to a different engine build, and I'm stumped on the oil feed. Conventional logic, as I understand it, is that the NA blocks are tapped for the oil feed from the factory, but don't drilled through into the passage. This block seems to have a small hole withing the M12 threaded hole that goes fairly deep into the block material. So it would seem at a glance to be done in this application. Only, this engine has never been turbocharged, and I didn't remove a plug from this hole when tearing it down. Does the hole need to go even further than the depth I've shown here with the drill bit? Am I missing something?

PXL_20230325_222022189.jpg

PXL_20230325_222030450.jpg

PXL_20230325_222148334.jpg

Link to comment
https://www.sau.com.au/forums/topic/484554-driling-oil-feed-in-23u-awd-block/
Share on other sites

2 hours ago, FiXtUrE said:

Measure the hole from which welch plug you’re going to remove/tap into. Earls fittings will braided lines should do the job, depending on the hole size.

I don't think that is good advice, if you attach a turbo oil feed to a welch plug you will get coolant, not oil in most cases.

In this case the oil feed seems to be there, it is just a question of making sure is connected right through.

  • Thanks 1
9 minutes ago, FiXtUrE said:

What remove Welch plug, add helicoil ( which will shorten/lower the thread size though for the fitting ) Otherwise tap a thread into the existing hole.

Mate, I don't know what is going on with your posts, but I can only think one 1 welch plug in an rb that goes to an oil gallery and it is not externally accessible (behind the oil pump). There is another in the rear of the head but it is to a void not a pressure source. 

Please post a pic with exactly which welch plug you think would be suitable for use as a turbo oil feed.

To OP, I don't have a disassembled block handy, but I believe the oil galleries are on the right side of the block, so yes it could be a pretty long passage. It looks like your sump is off so spin it over and have a look

I know the smart choice is to let this go, but FYI those welch plugs go to the water jacket and have coolant behind them, so would not be great as a turbo oil feed. OP is holding a drill, not pointing at the welch plug. Per their first pic, they are asking about the factory threaded hole in the block between cylinders 3 and 4

15 minutes ago, NZ-GTT said:

You may want to add another fool to your ignore list!

Considered it! It seems that our rocket surgeon has taken himself off to be an expert on Aliexpress lip extensions and body kit bullshit, in a part of the forum that I never visit. He hasn't been seen in the useful part of the forum for a week or so.

4 hours ago, GTSBoy said:

Considered it! It seems that our rocket surgeon has taken himself off to be an expert on Aliexpress lip extensions and body kit bullshit, in a part of the forum that I never visit. He hasn't been seen in the useful part of the forum for a week or so.

FiXtUrE after reading your comment.

image.thumb.jpeg.e6372facc3be052ac36d294ccd2646fe.jpeg

 

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Johnny is sad now... Because you didn't get Bosch Motorsport ABS.  
    • Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
×
×
  • Create New...