Jump to content
SAU Community

Recommended Posts

Hey all, on my Subaru I noticed I have a whistling sound when from 60km an hour onwards, below that I don't hear it. I used to hear it from 80km onwards but now it's 60km. It does seem to get louder then plateau's, I thought maybe it's the wheel bearings but I got them replaced about 70,000km ago, unless the mechanic put cheap ones on. What would you guys lean towards it being? Also when going over small bumps and especially when I'm turning the wheel on bumps I can hear like a twitching sound I think from the rear passenger side, maybe the strut? 

I know the rear of the car itself has been squeaky probably since I bought it (separate issue), but I've never fixed it as I generally don't have people sitting in the back and it's not overly noticeable unless I go over bumps with people in the back or if I'm driving myself but turn into a carpark ramp to go up the parking.

On 11/07/2023 at 10:35 PM, GTSBoy said:

You seriously want us to attempt to diagnose odd sounds over the internet?

To be fair something like every second engine issue thread starts with a recording of odd noises happening in the engine bay, no? In that sense I'd say having a recording would be good for a start.

44 minutes ago, soviet_merlin said:

To be fair something like every second engine issue thread starts with a recording of odd noises happening in the engine bay, no? In that sense I'd say having a recording would be good for a start.

Yeah, but when it's happening at 60+ km/h, good luck trying to get a recording that we can hear anything over the wind roar.

On 11/07/2023 at 9:34 PM, silviaz said:

I thought maybe it's the wheel bearings but I got them replaced about 70,000km ago,

Could still be wheel bearings. Or a diff? Dunno if that's a whistle, probably more a whir.

Sounds like the rear is unrelated? Hard to diagnose anything with the amount of info though. YOu could get under the back and just check everything is tight ?

5 hours ago, PranK said:

Could still be wheel bearings. Or a diff? Dunno if that's a whistle, probably more a whir.

Sounds like the rear is unrelated? Hard to diagnose anything with the amount of info though. YOu could get under the back and just check everything is tight ?

Bearings got replaced (could have been cheap ones, though I am leaning towards it), will get it checked out one of these days. Doubt it's the diff, can't hear it on passenger side only driver side.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
    • I've got MCA Blues on my V36 Skyline, and while I've managed to sort out issues with scrubbing/bottoming out by raising it a smidge and increasing the damping hardness, the rear end still sounds *super* noisy when driving on anything other than the flattest surface imaginable. It sounds like a small party of flamingos are just chatting away in the back, which makes me think there are several link points in the suspension contributing to the noise. Am I hearing dried out/worn bushings? None of it sounds like metal-on-metal, it sounds more like hard rubber squeaking on metal. It's been suggested that a bit of silicon spray on each bushing might quiet them down, but I'm not sure what material the current bushings are made of (probably factory, I imagine) and whether silicon spray will degrade that material.
    • The obvious answer here is get a ND2/3 RF with the Targa top. The red is nicer, too!
×
×
  • Create New...