Jump to content
SAU Community

Recommended Posts

Hey, is there a known restriction in the R34 GTT fuel return? I tested my fuel pressure with a Walbro 255, and have 52 psi at idle, with the regulator vacuum line on and off.

The only time I get 43 psi is if I fully disconnect the return line off the regulator and let it flow out into a bottle, so it seems to be something after the reg causing it.

I've disconnected both ends of the return line and I can blow through it. I went under the car and don't see any dents or kinks in the hard lines. I blew air into the return port of the fuel hat and it's harder to blow through, but I'm guessing that's because of that tank transfer valve attached to it. I’ve replaced the return lines from the reg to the hard lines as well

Any ideas? Thanks

Link to comment
https://www.sau.com.au/forums/topic/484962-er34-fuel-return/
Share on other sites

29 minutes ago, Dose Pipe Sutututu said:

Yeah the venturi/siphon inside the fuel tank lid.

Either you drill it out or replace it with a radium venturi/siphon or go tits out get a FFG fuel tank lid and replace the OEM unit.

Makes sense, I was thinking it had to be that thing. I will try modifying it first and see if I can get it to work. Is it drilling out the fittings on the hat, or drilling out the actual siphon pump?
IMG_1401.thumb.jpeg.327d0ab370bf04413efc17ce4d74b4e8.jpegIMG_1402.thumb.jpeg.91eee0fd4e0a5c42a6f8735e27d1ad9d.jpeg

2 hours ago, tylink720 said:

drilling out the actual siphon pump

It's a nozzle used to generate the suction. It's sized to produce enough suction with the stock fuel flow driving it. If you upsize the pump then you have to squeeze that increase through there. And you get LOTS of suction.

I don't know how much to drill it out. Remember that cross sectional area increases with the square of diameter, so you probably don't want to drill it out a lot, for "only" a 255L/h pump. You're up about 25-30% on stock capacity, so you probably only need about a 10-15% diameter increase.

  • Like 1
  • 2 weeks later...

I've drilled out the siphon pump to a little larger than stock, I think I used a 5/16 bit. Put it back together and still had the 50psi fuel pressure. Took it apart again and ended up breaking one of the fittings on my fuel hat which sucked, but luckily I was able to get a new one within a week. Fit the new hat, and tested the pressure with the siphon pump removed so it just pumps straight back into the tank, still 50psi. 

I have to assume now it's my return line that's the restriction. I was hoping it would be easy to replace the rear fuel lines that connect to the tank, but it looks like I'd have to lower or drop the tank which looks like a crap job. I will try using an air compressor first to blast out the return line and see if it does anything

24 minutes ago, tylink720 said:

I've drilled out the siphon pump to a little larger than stock, I think I used a 5/16 bit. Put it back together and still had the 50psi fuel pressure. Took it apart again and ended up breaking one of the fittings on my fuel hat which sucked, but luckily I was able to get a new one within a week. Fit the new hat, and tested the pressure with the siphon pump removed so it just pumps straight back into the tank, still 50psi. 

I have to assume now it's my return line that's the restriction. I was hoping it would be easy to replace the rear fuel lines that connect to the tank, but it looks like I'd have to lower or drop the tank which looks like a crap job. I will try using an air compressor first to blast out the return line and see if it does anything

You had the same idea I did. If that doesn't do it start measuring pressure at various points in the system, the pressure drops at each point will tell you where the restriction is. Could be an FPR too. If you've hardwired your fuel pump to run full blast all the time the FPR is almost certainly your problem at idle. Nissan used the FPCM to slow down the pump at idle.

Edited by joshuaho96
  • Like 1

Try bypass the fuel dampener to see if there's still an issue.

R34 GT-t uses a couple of them instead of 1x like the R33.

If that solves the issue, then delete the OEM ones and install an aftermarket one like a Radium one.

 

In the past, on S15s (same fuel tank hat/lid as the R34) I enlarge the siphon/venturi and it fixes the issue. Was hoping that was enough for you.

  • Like 1
On 10/4/2023 at 2:35 PM, joshuaho96 said:Could be an FPR too. If you've hardwired your fuel pump to run full blast all the time the FPR is almost certainly your problem at idle. Nissan used the FPCM to slow down the pump at idle.

I don’t think it’s the FPR as I’ve run a short hose into a bottle straight off the reg, and the pressure drops down. Maybe a new reg is a good idea anyway though. I will try doing what you said and test down the line. Although the only spot I can measure is between the hard line and tank, but it’s cramped as in there. I’ll have to lower the tank to get in there. 

On 10/4/2023 at 5:47 PM, Dose Pipe Sutututu said:Try bypass the fuel dampener to see if there's still an issue.

R34 GT-t uses a couple of them instead of 1x like the R33

Yep I bypassed the dampener on the fuel return line too but didn’t help. I still have the dampener on the feed. Maybe I’ll test bypassing that one too as I put the gauge before it. 

15 hours ago, Dose Pipe Sutututu said:

Hang on, are you running the stock FPR? If so, get an aftermarket one

Yep stock reg. Ill look into a new reg, just seems strange that it drops the pressure fine when I remove the return line. Also seen posts on here saying the stock reg is good for mild pump upgrades. It is 25 years old I guess

1 hour ago, tylink720 said:

 Also seen posts on here saying the stock reg is good for mild pump upgrades.

Car still might work however the fuel pressure is probably all over the shop like you've just discovered.

1 hour ago, Dose Pipe Sutututu said:

Car still might work however the fuel pressure is probably all over the shop like you've just discovered.

Alright, I've started looking for an aftermarket reg. This cars been a bottomless pit so far, and I haven't even started the proper power mods yet lol.

thanks

5 hours ago, tylink720 said:

Yep stock reg. Ill look into a new reg, just seems strange that it drops the pressure fine when I remove the return line. Also seen posts on here saying the stock reg is good for mild pump upgrades. It is 25 years old I guess

If you want to run the stock regulator you need to keep some method of making sure you aren’t trying to flow 255lph of fuel at idle. Otherwise you will experience what you’re talking about. 

  • Like 1
2 hours ago, tylink720 said:

 This cars been a bottomless pit so far, and I haven't even started the proper power mods yet lol.

Welcome to Skyline ownership, cheaper and more reliable buying a BMW M2 Comp, but here we all are lol.

1 hour ago, Dose Pipe Sutututu said:

Welcome to Skyline ownership, cheaper and more reliable buying a BMW M2 Comp, but here we all are lol.

Yep lol, half the fun is working on these piles. My brother has a newer BMW and it’s super quick and reliable

Any current recs for a good budget reg? I don’t want to buy some cheap eBay stuff, but also don’t want to drop $500 on just a regulator. I’ve seen some for about $140-$170 like Tomei, P2M, NRG, AEM, ect

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...