Jump to content
SAU Community

Recommended Posts

My RB25 is lately struggling to get to 5k rpm it feels like it's not boosting. It gets to about 4.5-5k then splutters. It is usually 580hp and would usually scream instantly to 7k rpm in seconds. I have also noticed it is idling really high. Like 1500 rpm which makes me think maybe a vac hose has come off or something. The microtech dash is reading boost but I am not feeling it. If idle is high, would that suggest vac is leaking somewhere after the throttle body?

Link to comment
https://www.sau.com.au/forums/topic/485034-boost-gone-missing-rb25/
Share on other sites

When I get a chance I will suss out where everything is connected.

the weird thing is it seemed to start when I put E85 from a different servo than my usual United. My fuel pumps were making a strange high pitch noise for a bit. Not sure if it is coincidence.

btw you seem to reply to every single post in this forum. Are you the administrator?

I'm not an admin here. Just seem to be always in front of a computer.

The different fuel thing is an additional confusion. If it were just a bit short on ethanol content, it really shouldn't cause you to lose boost and make less power. If anything, because it would be more likely to ping, it should make more power - for a little while.

And if it were 98 by accident, it really should ping, although it would be as rich as hell, so there's competing mechanisms there. The MT is not smart enough to do anything about knock, so it should all just happen without any reaction. I'd expect smoke, either way.

A high idle does make it sound like something is open, or just perhaps (and worse), something broken.

How much boost is missing? 16ish psi on the dash. Is that normal?

I have just had a thought. Possibly a fuel related problem could have caused high exhaust temps, could have collapsed the cat. That would slow it down while still allowing boost to show normal.

The fuel was E85 the only thing that made me wonder if it is a fuel issue was the sound from the fuel pumps. I have had 2 tanks of fuel since. Think 16pounds is normal. Tbh I never even took notice of the boost previously. The engine seems to be really well built judging by the quality of the install and the parts. I will make sure all connections between pipes are tight, I may also chuck a new set of plugs and see if that helps. My idle has always been a bit over the place. 
when cold the idle fluctuates a lot when warm sometimes I will sit at lights at 1000 sometimes it will be 1100 and like yesterday it was a steady 1500. Maybe wherever the leak is is progressively getting bigger 

5 hours ago, OO Dan OO said:

The fuel was E85 the only thing that made me wonder if it is a fuel issue was the sound from the fuel pumps. I have had 2 tanks of fuel since. Think 16pounds is normal. Tbh I never even took notice of the boost previously. The engine seems to be really well built judging by the quality of the install and the parts. I will make sure all connections between pipes are tight, I may also chuck a new set of plugs and see if that helps. My idle has always been a bit over the place. 
when cold the idle fluctuates a lot when warm sometimes I will sit at lights at 1000 sometimes it will be 1100 and like yesterday it was a steady 1500. Maybe wherever the leak is is progressively getting bigger 

Start by searching for a boost leak/vacuum leak. That is the first port of call if your idle is weird.

1 hour ago, OO Dan OO said:

I have heard FG Barra plugs are good but not sure if they will fit the RB

Um. Wat? Just use the correct plugs. It's not like they're in any way difficult to get hold of.

1 hour ago, OO Dan OO said:

Also can anyone ID these Coils?

The blue makes them look like Splitfires. But there have been cheap/shit/nasty technicolour yawn coils out there in the same blue as Splitfire, so how can we tell from that photo? Why don't you pull one out and have a look at it?

6 hours ago, GTSBoy said:

Um. Wat? Just use the correct plugs. It's not like they're in any way difficult to get hold of.

The blue makes them look like Splitfires. But there have been cheap/shit/nasty technicolour yawn coils out there in the same blue as Splitfire, so how can we tell from that photo? Why don't you pull one out and have a look at it?

I was just looking at the ford ones because a very reputable tuner said they are really efficient for high boost applications. That was for a JZ though. My next move is to swap the plugs n check the coils out.

Ok so here is where I am at.

i have checked IC connections and boost lines.

changed spark plugs

changed TPS

after changing the plugs it seems to idle better when cold but I still have the same issue. I is really hard to get even to 5 grand it's just holding back big time? What fuel pressure should I be looking for?

 

On 11/12/2023 at 9:37 AM, OO Dan OO said:

Ok so here is where I am at.

i have checked IC connections and boost lines.

changed spark plugs

changed TPS

after changing the plugs it seems to idle better when cold but I still have the same issue. I is really hard to get even to 5 grand it's just holding back big time? What fuel pressure should I be looking for?

 

What plug gap are you set to?

 

Do you have a factory fuel pressure reg, or an aftermarket one?

 

If it's aftermarket, it should be set to what ever pressure it was running when tuned. Typically it'd close to factory pressure, but I'll never trust anyone who is setting up aftermarket parts on a vehicle.

  • 4 weeks later...

I gapped my plugs to .7, I did find some significant boost leaks. Which are now fixed but... no change from my initial problem. I did find a black mark that could possibly be rogue spark on one coil pack shaft, along with my fuel pumps (2x044) sounding a bit strange.

So to recap 

-new TPS

-new plugs .7

- boost leaks fixed

On 30/10/2023 at 8:41 AM, OO Dan OO said:

....the weird thing is it seemed to start when I put E85 from a different servo than my usual United. My fuel pumps were making a strange high pitch noise for a bit. Not sure if it is coincidence.....

Well, the clue was there

13 hours ago, OO Dan OO said:

**fixed**
dirty fuel filter after all that

But no-one guessed it! Internet mechanicing fail 

On the bright side, at least the car was misfiring instead of running lean enough to kill the engine, so that is a win.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just had this happen to me too.  R32 GTR.   Also broke "just before going out onto the track" - someone up there is looking out for us... Very scary since I was about to do a narrow street course with zero run-off and curbs everywhere. Many people on here upgrading to billet uprights and R35 bearings?   Or buying new OEM knuckles?  I am not keen to replace with another s/h 30 year old fatigued part.
    • Top off with distilled water and see what happens. If you keep losing coolant then you know to start looking.
    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
×
×
  • Create New...