Jump to content
SAU Community

Fuel pressure falls to zero at idle and stalls.

Tim32
 Share

Recommended Posts

Tim32 Apprentice

Tim32

Posted
Posted (edited)

Hey guys, I did a smoke test this week chasing vacuum leaks and found two leaks which I fixed up... Now having a weird issue where it starts and at idle after a few seconds the fuel pressure suddenly goes to 0 and stalls.. if I blip the throttle, it will regain pressure and keep going though. I put a new fuel filter on and drained the old fuel and put new fuel in but maybe thats stirred up some crap in the fuel tank and blocked the intake or something??? Any other ideas? FPR stuffed?

EDIT: Also, when it stalls, the pump primes and pressure goes back up and it starts again as per normal and happens all over again.

Edited by Tim32
joshuaho96 Veteran

joshuaho96

Posted
Posted
1 hour ago, Tim32 said:

Hey guys, I did a smoke test this week chasing vacuum leaks and found two leaks which I fixed up... Now having a weird issue where it starts and at idle after a few seconds the fuel pressure suddenly goes to 0 and stalls.. if I blip the throttle, it will regain pressure and keep going though. I put a new fuel filter on and drained the old fuel and put new fuel in but maybe thats stirred up some crap in the fuel tank and blocked the intake or something??? Any other ideas? FPR stuffed?

EDIT: Also, when it stalls, the pump primes and pressure goes back up and it starts again as per normal and happens all over again.

Check your FPCM. What happens if you bypass it? The ECU will bypass it during prime + initial start, then the FPCM kicks in and slows the pump down.

MBS206 Grand Master

MBS206

Posted
Posted

If you've been mucking with vacuum lines, start there, and check you have your vac line on properly, and on a vacuum line that isn't flowing air, it's just a vacuum source.

 

When you measure your fuel pressure, are you measuring absolute fuel pressure, or gauge pressure compared to the inlet manifold?

Tim32 Apprentice

Tim32

Posted
  • Author
Posted

Hey guys, thanks for the replies! (We are noobs so sorry if some of this seems obvious or is completely wrong)

@joshuaho96 I did go looking for the FPCM (after googling) but it's an old drift car so I think that has been bypassed already, the fuel pump is wired directly to the battery.

@MBS206 OK I'll double check vacuum lines. I'm just looking at the FPR gauge, shows around 40PSI while priming and idle, until instant drop to 0, not even a slow drop, like instant.

 

MBS206 Grand Master

MBS206

Posted
Posted
1 hour ago, Tim32 said:

Hey guys, thanks for the replies! (We are noobs so sorry if some of this seems obvious or is completely wrong)

@joshuaho96 I did go looking for the FPCM (after googling) but it's an old drift car so I think that has been bypassed already, the fuel pump is wired directly to the battery.

@MBS206 OK I'll double check vacuum lines. I'm just looking at the FPR gauge, shows around 40PSI while priming and idle, until instant drop to 0, not even a slow drop, like instant.

 

How is the Fuel pressure gauge connected, show photos, what's it referencing etc.

 

Get photos of how the fuel pump is wired.

I'm assuming there's a relay triggering it, if so, measure what the signal wires are doing. From memory the ECU pulls to ground, so find the coil wire that goes to the ECU and measure resistance to ground.

 

If it's an old drift car, what ECU is in it?

TurboTapin Experienced

TurboTapin

Posted
Posted
9 minutes ago, Tim32 said:

Here's some pics, ECU is stock. thanks again.

IMG_3128.jpeg

IMG_3127.jpeg

That wiring looks like it was done by a 12 year old with a methamphetamine addiction. Start by redoing that disaster. What you're describing has nothing to do with your FPR vac source. 

  • Haha 2
MBS206 Grand Master

MBS206

Posted
Posted

I gotta agree that FP wiring looks, interesting.

And questionable.

 

I'd be doing some probing to see what circuit is shutting off.

It actually sounds like FPCM wiring is partly in use.

Priming, starting are all at full power from memory, then a few seconds later drops to half strength, and it looks like that signal isn't getting to your FP, as a hypothesis that is.

 

Needs more probing on a multimeter being done.

joshuaho96 Veteran

joshuaho96

Posted
Posted
1 hour ago, MBS206 said:

I gotta agree that FP wiring looks, interesting.

And questionable.

 

I'd be doing some probing to see what circuit is shutting off.

It actually sounds like FPCM wiring is partly in use.

Priming, starting are all at full power from memory, then a few seconds later drops to half strength, and it looks like that signal isn't getting to your FP, as a hypothesis that is.

 

Needs more probing on a multimeter being done.

This is exactly what I was thinking, I just wasn't expecting whatever that hackjob was. Skyline owners never disappoint.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      Welcome back brother 
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...