Jump to content
SAU Community

Recommended Posts

These are those $13,990 Excels from 1997 right? They were flimsy when they were brand new 🙂..... The work those guys did on that car to make it as safe as it was in that incident is phenomenal.

  • Like 1
On 02/06/2024 at 9:41 PM, Rezz said:

These are those $13,990 Excels from 1997 right? They were flimsy when they were brand new 🙂..... The work those guys did on that car to make it as safe as it was in that incident is phenomenal.

Yeah you can pick them up for $1000 now, good condition road going ones for $3000. They handle OK for a FWD and the power to weight ratio's not too bad. Great little nugget to get into racing, and shitbox rallying etc.

  • Like 1

Absolutely. Not knocking their ability on track at all, looks like a whole heap of fun. Just the crash safety aspect which I had my doubts about which those guys where able to engineer out of it 😄

Edited by Rezz
On 04/06/2024 at 2:42 PM, funkymonkey said:

Yeah you can pick them up for $1000 now, good condition road going ones for $3000. They handle OK for a FWD and the power to weight ratio's not too bad. Great little nugget to get into racing, and shitbox rallying etc.

 Absolutely. Not knocking their ability on track at all, looks like a whole heap of fun. Just the crash safety aspect which I had my doubts about which those guys where able to engineer out of it 😄

On 6/4/2024 at 3:42 PM, funkymonkey said:

Yeah you can pick them up for $1000 now, good condition road going ones for $3000. They handle OK for a FWD and the power to weight ratio's not too bad. Great little nugget to get into racing, and shitbox rallying etc.

Chatting one someone recently at racing them at QR.

They say you can't take turn 2 in one flat stick in 4th. They don't have the torque to pull them selves straight, so make sure you're ringing it's neck out in 3rd instead :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...