Jump to content
SAU Community

Recommended Posts

Is it safe to take the redline up to 7500rpm or so? With stock internals, and a PowerFC. I've got an adjustable exhaust cam gear so that should help with any breathing problems, but I'm also worried about affecting the longevity of the engine.

Link to comment
https://www.sau.com.au/forums/topic/49107-increasing-redline-on-rb25/
Share on other sites

  • Replies 156
  • Created
  • Last Reply

Top Posters In This Topic

Long term = completes a track session

Standard internals = un-opened motor

:D

:cheers: always the realist ;)

I took mine to 7500rpm no drams for over 12 months.

Motor died - but that wasnt due to revs, just a few too many psi snuck in one night and caused it to ping.

So 7500 all the way.

Although, i found with stock cams, the car didnt have any go after about 7300 at that was still pushing it.

Also due to many other factors aswell im sure, like ECU and all sorts of other things

There is no point at all to increasing the redline, You will lose so much power after 6500RPM that its not even worth it. It may seem like its still pulling but on the dyno it shows that the HP drops like hell.

Although, i found with stock cams, the car didnt have any go after about 7300 at that was still pushing it.  

Also due to many other factors aswell im sure, like ECU and all sorts of other things

I'm only considering it because I've got an exhaust cam wheel, and will be running 15 psi after the tune. I used to run 15psi with the factory ECU, but the PowerFC at the same boost maxes out my injectors and AFM. So I'm running at 11psi until I get it tuned.

Anyway I'll see what the mechanic has to say when I take the car in. At least now I know I have some room to experiment.

I've run my Skyline up to 7500 for over 9 months now, I have had no drama's with this setting, however yes in Dyno runs I have found that there is no real power increase around the 6500 mark. I am running a Haltech E6K I think with a Stock engine and turbo along with ARE intercooler. I pulled about 187kw out of the rear wells and about 1350nm of Torque which I thought was quite high but this has been verified by two different dyno stations.. Also running the stock turbo at 14psi with a 3" Dump running into a Apexi 3.75 cat back exhaust.. (yes it scraps everywhere). I did a recent check and found compression to be around 135-150 over all 6 cylinders.. I have been told this is about right for a skyline, I dunno? shrug :P I think that a GT2540 would be great to upgrade to with new 700+cc injectors with fuel rail and pump to be upgraded as well. What ya think? do you think a new Cam gears would be wise too?

Aridyne

The exhaust camwheel retarded 3 or 4 degrees is good for enhanced torque low and midrange. In all our dyno runs stock and modified power tended to drop off fairly sharply over 7000. In the early days we hit 8200 on a regular basis.....but not anymore. After 3 years of street/drag/track the engine still doesn't use any oil between 5K changes so I guess the revs didn't hurt it any. When you get it tuned and see your power curve then you can decide on your rev limit

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...