Jump to content
SAU Community

Recommended Posts

Normally, when you travel over about 20 km/hr the door's automatically lock.

I found this annoying so decided to remove this function.

Firstly, remove the glovebox, theres about 4-6 screws holding it in and clips on the left hand side, be careful not to break them.

You will see a black box on the left hand side, this controls the central locking.

To make sure you have the right box, trigger the central locking and you will hear a clicking noise coming from the box.

Cut the green wire going into the box as shown in the picture.

All done!

Put the box and glovebox back together again.

Thanks to MadYeti on SDU for the information on which wire to cut.

Dave

  • 2 weeks later...
  • 3 weeks later...
  • 7 months later...

ok .. i have a prob

i cut the green wire, but the door still locks itself

errrmmm so what wire did i cut lol

havent noticed the car do anything strange yet, so i hope it wasnt a vital wire

lol

-Ruffels

  • 4 weeks later...

I DO have a viper alarm... you could be right.... At the moment the siren goes off it's banana unless you have the disable key in it.... washed the engine bay out this morning, must have some kind of short... hopefully it will clear eventually!

  • 3 weeks later...

definately doesn't lock here at any speed, and as far as I can tell, there are no wires cut anywhere, and I've been in the door well too, and nothing cut there.

I would like it to lock at 25km and lock when key removed if anyone knows how to get it to this without it being a function of an aftermarket alarm :(

  • 1 year later...
series 2 - locks about 5 seconds after the ignition turns on! i'm used to it... it unlocks when you turn the motor off, do the series 1 do that too?

I have a series 1 and it locks both doors after 20k's or so and when the ignition is turned off it only unlocks the drivers door.

I have a bit of shit i take to work with me and instead of dragging my bag out of the drivers door i go around to the passenger side and ge it, i have to arm and dis-arm the alarm every time coz i forget to unlock the passenger door before i get out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m here solo don’t have any hands to help so haven’t hit it with a timing light 
    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
×
×
  • Create New...