Jump to content
SAU Community

Recommended Posts

just wondering, my car is blowing too much white smoke just like the smoke when u turn your car on on a cold early morning...everytime i accelerate even a bit it blows a fair bit of white smoke. does that mean im burning oil or fuel? i got my car dyno tested and it is running too lean...

Link to comment
https://www.sau.com.au/forums/topic/50945-my-car-is-blowing-white-smoke/
Share on other sites

or more like ringlands. If its running lean!

What to do:

1) smoke smell like oil - and if its gets worse and worse, Piston number 6 is dead

2) Look down at the exhaust manifold too see if theirs any oil leaking out were the manifold joins onto the head.

3) leak down compression test

yeah it has a smell like oil and yeah my oil is burning pretty quick lately...i haventdriven the car much, its only my weekend car... but yeah ill check it out tomorrow.

so white smoke is pretty then aint it.i hope its nothing serious becasue my mechanic has been so busy and can only see him on the 25th...maybe i should take it to someone else asap before anything else goes wrong...maybe also the cause why my car is so laggy at the start and only picks up once it hits 4000rpm...

check your IC piping...if there is oil inside the piping / intercooler your turbo is going out...mine is doing the same thing and just spews out oil from the compressor side into the intake tract and burning in the engine out the exhaust...WHITE SMOKE... that is your problem most likely.

If I don't give the car a few mins to warm up as it hits boost it will blow puffs of what looks like white smoke.

Driving behind the car it looks more like fuel (grey smoke) than oil.

Mine has done it for around 2.5years and ~100,000km's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...