Jump to content
SAU Community

Recommended Posts

  • Replies 334
  • Created
  • Last Reply

Top Posters In This Topic

JAD :) that comes as no surprise :P

Careful monkey, we don't want to be accused of slander. I will say I found Anton @ JAD quite helpful, but maybe the is not indicative.

As for the exact documents you need, perhaps we could start a sticky:

15 Year Rule

Import Approval:

* A completed Import Approval form.

* The supplier invoice.

* Proof of age (usually the Japanese deregistration papers)

* An authorised photocopy of your license.

Customs & AQIS Clearance:

* Import Approval granted by DOTARS

* Bill of Lading

* Degassing documentation or an exemption by the Dept. of Environment.

Perhaps others could elaborate and add stuff for SEVS (in a rush to get out the door ATM).

LW.

the more i read this post the more it makes me freak out :P

steve

Don't be. Its just a slow cumbersome process all round where you are always reliants on other people and entities to process things in a timely manner, and often you can't get in contact with them directly.

Just plan ahead, read all the documentation, make sure you fill out all the forms correctly, and maybe make the odd sacrifice or two :)

LW.

Careful monkey, we don't want to be accused of slander. I will say I found Anton @ JAD quite helpful, but maybe the is not indicative.

As for the exact documents you need, perhaps we could start a sticky:

15 Year Rule  

Import Approval:

* A completed Import Approval form.

* The supplier invoice.

* Proof of age (usually the Japanese deregistration papers)

* An authorised photocopy of your license.

Customs & AQIS Clearance:

* Import Approval granted by DOTARS

* Bill of Lading

* Degassing documentation or an exemption by the Dept. of Environment.

Perhaps others could elaborate and add stuff for SEVS (in a rush to get out the door ATM).

LW.

For SEVS:

Import Approval:

* Sign agreement with an approved RAWS for your model

* DOTARS Import approval - your RAWS applies for this for you - You do not need to provide ID or De-reg document to get this under SEVS

Customs and AQIS:

* Import Approval

* Bill of Lading (B/L)

* Photocopy of your RAWS license to import pre-charged equipment (aircon)

* Clear photocopy of license

When you go to pickup your car:

* Delivery order for AAT (Australian Amalgamated Terminals) which will be provided by your customs agent

* AQIS inspection sheet

* Bill of lading

When you go for steam cleaning:

* AQIS Sheet

When you go to the compliance center:

* Original De-registration sheet from Japan

Throughout the entire process:

* A very open wallet :P

Careful monkey, we don't want to be accused of slander. I will say I found Anton @ JAD quite helpful, but maybe the is not indicative.

As for the exact documents you need, perhaps we could start a sticky:

15 Year Rule  

...

LW.

Thankyou very very much for this information, i am upto the "apply for import approval" stage, currently waiting on deregistration documents.

I believe my car was manufactured in November, does this mean i can't apply for approval until november, or can i send it off a bit earlier than this?

Thanks,

-Patrick

Steam cleaning cost me $210.10 and they basically didnt do a single thing to the car. There is absolutely no discernable difference from when i took it there to when i took it home.

I paid the $210.10 and said thanks very much but inside i was thinking this is the biggest ****ing rort ever.

Thankyou very very much for this information, i am upto the "apply for import approval" stage, currently waiting on deregistration documents.

I believe my car was manufactured in November, does this mean i can't apply for approval until november, or can i send it off a bit earlier than this?

Thanks,

-Patrick

Express post them on the last day of October.

Anyone care to name the Melbourne broker that went out of business? Reason I ask is that I am in the middle of a situation that has seen my car sit at the docks for over 6 months with storage fees accruing daily. The bottom line is, if I want to have my car, then I will have to pay the shipping and customs fees all over again due to this broker's company going under. This will mean that the cost of getting the car here will be similar to actually buying the car. Not happy.

Anyone care to name the Melbourne broker that went out of business? Reason I ask is that I am in the middle of a situation that has seen my car sit at the docks for over 6 months with storage fees accruing daily. The bottom line is, if I want to have my car, then I will have to pay the shipping and customs fees all over again due to this broker's company going under. This will mean that the cost of getting the car here will be similar to actually buying the car. Not happy.

That is Fuct... :rolleyes:

I just got a phone call from the importer who has advised me that my car is ready to be picked up. I just need to get the dispatch papers from the shipping company and then get to the storage depot on Monday morning and pick it up.

Do you mean you need the original piece of paper (ie. sent via mail from Japan) or just a copy of the de-reg paper?

LW.

Lucien, for 15yo you just need copy, for SEVS I understand you need orig.

Richard

mmmgtir: That's interesting.

Hmmm, well I have just been emailing Colin @ CGL. Looks like I can't even arrange a viewing of my car when it lands, which seems rather sucky. Also, they can't suggest (or rather can't be bothered to do) anything about the wheels travelling in the car. Best they can come up with is to "cross our fingers" and "just have to have everything cleared and ready to go as quick as possible". :uhh:

All of which is kind of irritating. It would also help if Colin actually read my emails a little more closely, rather than me having to re-ask the same question in about three different emails (and not getting any clear response to some other questions).

LW.

Hmmm, well I have just been emailing Colin @ CGL.  Looks like I can't even arrange a viewing of my car when it lands, which seems rather sucky.  Also, they can't suggest (or rather can't be bothered to do) anything about the wheels travelling in the car. Best they can come up with is to "cross our fingers" and "just have to have everything cleared and ready to go as quick as possible".

I asked whether I could get to see the car the day after it got here but was told that would be 'very difficult'. I didn't press the issue as I could see I was pretty much going to get nowhere from the response I got...

Interestingly not a word about aircon requirements and there's nothing about it on the copy of the customs clearance doc I was faxed this afternoon. I asked the CA about any paperwork I might need to fill in, but he said not to worry about it and that he'd just put the car through and see what happens. Of course I could still see some something from the DEH down the track, but if I get nothing all those people that paid to have their car de-gassed in Japan will have every right to be p'd off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...