Jump to content
SAU Community

Recommended Posts

took the car for a spin yesterday, just for the hell of it, before taking it to the electrican, had a mate in the car so i dumped it and its started to spin the passenger side wheel then knocked it into second still spinning but changed to the drivers side wheel spinning?? i'll put up a pic of the black lines as its even funny to look at.. anyone know while this would happen???

Cheers Matt.... dam it was good to drive her again...

Link to comment
https://www.sau.com.au/forums/topic/51368-i-think-my-diff-is-broken/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

its been sitting a while, right?

flog it a bit then change the oil...the plates are prolly seized and have only let go on one side....it should free up... but if it doesnt....u need a rebuild.

also another thing is that when i have the car off the ground and spin the wheels by hand one will spin one way and the other will spin the other?? the cars at the auto electrican at the moment which is across the road from my machanics which is were the car is going next, swapping over the rear calipars and hand brake set up so i'll get him to change the diff oil to one of the ones above then too. thanks for ya help

Same brands as any oil you would use in a open wheeler diff....just that they formulate it specifically(sp?) for lsd's

Same deal as engine oils....different formulas and viscosities for different applications.

Open wheeling diffs will spin the other side wheel the other way when car is jacked up.....clutch pack type(plate) Lsd's will do the same just a little bit until the lsd unit kicks in(which is like 1/10th of a turn- not much) if the plates are not working properly like in RSX84's case, it will operate exactly like an open wheeler. because the slip is not limited.....this is assuming that his is a clutch type Lsd.

If it is viscous, then im unsure how it works but my understanding is the the oil in the viscous unit is forced thru little valves in the unit thereby causing both wheels to turn because the oil does not freely flow.......so i dont know how it would act in a jacked up situation because you wont be able to exert enough force by hand to make it work correctly.....

I know what I meant but I dont know if I have made it clear...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...