Jump to content
SAU Community

Recommended Posts

took the car for a spin yesterday, just for the hell of it, before taking it to the electrican, had a mate in the car so i dumped it and its started to spin the passenger side wheel then knocked it into second still spinning but changed to the drivers side wheel spinning?? i'll put up a pic of the black lines as its even funny to look at.. anyone know while this would happen???

Cheers Matt.... dam it was good to drive her again...

Link to comment
https://www.sau.com.au/forums/topic/51368-i-think-my-diff-is-broken/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

its been sitting a while, right?

flog it a bit then change the oil...the plates are prolly seized and have only let go on one side....it should free up... but if it doesnt....u need a rebuild.

also another thing is that when i have the car off the ground and spin the wheels by hand one will spin one way and the other will spin the other?? the cars at the auto electrican at the moment which is across the road from my machanics which is were the car is going next, swapping over the rear calipars and hand brake set up so i'll get him to change the diff oil to one of the ones above then too. thanks for ya help

Same brands as any oil you would use in a open wheeler diff....just that they formulate it specifically(sp?) for lsd's

Same deal as engine oils....different formulas and viscosities for different applications.

Open wheeling diffs will spin the other side wheel the other way when car is jacked up.....clutch pack type(plate) Lsd's will do the same just a little bit until the lsd unit kicks in(which is like 1/10th of a turn- not much) if the plates are not working properly like in RSX84's case, it will operate exactly like an open wheeler. because the slip is not limited.....this is assuming that his is a clutch type Lsd.

If it is viscous, then im unsure how it works but my understanding is the the oil in the viscous unit is forced thru little valves in the unit thereby causing both wheels to turn because the oil does not freely flow.......so i dont know how it would act in a jacked up situation because you wont be able to exert enough force by hand to make it work correctly.....

I know what I meant but I dont know if I have made it clear...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Just don't use ChatGPT or any other artificial stupidity for the equivalent of googling. Their demonstrated inability to discriminate reality from hallucination should be enough to make them totally untrusted. LLMs don't know anything and cannot think to even the smallest extent. They are just predictors of the next word, and that should never be confused with capability.
    • I think, given the usage model described in the OP, I'd never ever experience the wonders of the 400kW upgrade. What I really need is boost from 2000rpm and probably no more than 260-270rwkW. But I suspect that the highflow is not actually the turbo for that purpose, so I may in fact need to get a G25 or 30 or something right sized and very spooly. We shall see after it is tuned. I've had to back the boost and boost ramp off to stop the thing from pinging since the highflow went on, so I've been almost living the NA life for 9 months now! Injectors are recently in hand. AFM is in hand. Dyno is fixed. Just need to clear a queue of f**king Supras out of the way (and probably fit my new gearbox). So....some time this year? Lol.
    • For what I gather is a Sunday/summer car....braided is fine. You're not going to be left without a vehicle and you have plenty of time for inspection/maintenance. Oof. I wouldn't use them that way. They can probably handle the temperature** but the internal corrugations means that their flow characteristics are a bit shit. Lots of extra friction and pressure loss. Makes them flow like the next pipe size down. ** They are stainless, and the stainless can usually be at least something like 304L, which is pretty good at higher temperatures (unlike 316L, which I would use for a wrt/corrosive environment, but not a particularly hot environment). But the welding needs to be top notch. And even then, because you usually need at least one cone-seat end on them (because you can twist the hose and do up both ends at the same time unless one of them is a union) they can be prone to coming loose with heat cycles.
    • I don't have the OEM oil feed lines though and the turbo-wraparound line is torn, only has water. My plan is to get replacements for these and just connect a braided line to there. And make sure it's leak free. Hoses like these are also sometimes used to connect external wastegates, so for an EGR I think you're good using them.
    • Alright I understand. The most likely case is probably gonna be that I just keep the OEM unit in the car as long as it works.
×
×
  • Create New...