Jump to content
SAU Community

Recommended Posts

I've got a 1998 RS260 so the RB26DETT from a R33 GTR.

Put it on the dyno last weekend and it only pulled 110kws with 4psi boost?

I've just brought a power fc from japan and looking to get a Turbosmart E boost street.

What could be to problem before I put the parts on and tuned.

I would think it should have more power than that standard.

Thanks

Nick

I've got a 1998 RS260 so the RB26DETT from a R33 GTR.

Put it on the dyno last weekend and it only pulled 110kws with 4psi boost?

I've just brought a power fc from japan and looking to get a Turbosmart E boost street.

What could be to problem before I put the parts on and tuned.

I would think it should have more power than that standard.

Thanks

Nick

I dont know much but Id say the 4psi of boost will be part of the problem, for sure. What were the AFRs? Could be running very rich too.

Well thats what i think. I cant understand why its running 4psi. It should be waste gate pressure.

I'm hoping to be over 200kwsatw once tuned and 10-14 psi on the standard turbos.

Anyone know what the R33 gtr turbos will run?

Nick

I think 10psi is standard. 14psi is about the max you want to run safely. I'm running 13psi on my 260RS and have 200kwatw. Perhaps you have a blocked cat or a boost leak or something like that. 4psi is less than actuator pressure I think.

Impul ecu run just happened, much better than last time.. 173.5kw on the same dyno (we made a whopping 126 last time), and a stack more torque too! :D

post-69799-1284615768_thumb.jpg

A bit rich but more than liveable Dunc, I wonder if it is just running out of injector at max revs... :dry:

A bit rich but more than liveable Dunc, I wonder if it is just running out of injector at max revs... :dry:

Knew there was something else I was meant to ask about :D next time.

What'd reckon my target AFR's should be? I'd assume at this point the only way to get it better leaner (aside from waiting for the Impul to self tune) is either emanage or an AFC?

Knew there was something else I was meant to ask about :dry: next time.

What'd reckon my target AFR's should be? I'd assume at this point the only way to get it better leaner (aside from waiting for the Impul to self tune) is either emanage or an AFC?

Yep, dont bother with the AFC, Emanage is very good at what it does and will allow multiple maps (e85 hint hint) and self tuning with a wideband.

You should be aiming for flat 12afr at full throttle, right through the revs. You are safer than that so theres no issue (other than fuel consumption) but if you notice it leans back out to 12 at the end, im just not sure what caused it. The injectors should be good for over 220. Perhaps its the pump but I would say its just a weird tune. Looks like you picked up a good one there. :D

Nice result Dunc.

Stock boost on your car is 12psi.. If you did the bypass on the boost solenoid you can have unlimited boost.

I think Craig has seen 24psi using my Impul ECU at the moment as there is no boost cut on this ECU.

Cheers

Andy

Stock boost on your car is 12psi.. If you did the bypass on the boost solenoid you can have unlimited boost.

I think Craig has seen 24psi using my Impul ECU at the moment as there is no boost cut on this ECU.

Hrm weird, I did do the bypass. Manifold pressure graph looks like it maxed out at 15psi though :dry: last time I maxed out at less than 10 pounds though.

Edited by Dunc
Hrm weird, I did do the bypass. Manifold pressure graph looks like it maxed out at 15psi though :dry: last time I maxed out at less than 10 pounds though.

May have something to do with the exhaust? I know that Craig has 3" from the turbo back, so less restriction.

Can't remember what you have Dunc (is it just the group buy dump and stock exhaust?)

May have something to do with the exhaust? I know that Craig has 3" from the turbo back, so less restriction.

Can't remember what you have Dunc (is it just the group buy dump and stock exhaust?)

ah good point. At the moment Ive got a stock dump, with a 2nd cat in the pipes, and a nismo adjustable exhaust muffler (which was set to sport for the run). Might need to give that new group buy dump some consideration.

Edited by Dunc
ah good point. At the moment Ive got a stock dump, with a 2nd cat in the pipes, and a nismo adjustable exhaust muffler (which was set to sport for the run). Might need to give that new group buy dump some consideration.

Even if you don't touch the rest of your exhaust, change the dump pipe.

Certainly the biggest power boost when you do this. There is a massive cat in the middle of the stock dump that is soo restrictive.

On my car with the stock turbo I have seen 20psi when I did the bypass. Not for long as I don't thing the ceramic turbine will be happy for long even with a ball bearing core.

Even if you don't touch the rest of your exhaust, change the dump pipe.

Certainly the biggest power boost when you do this. There is a massive cat in the middle of the stock dump that is soo restrictive.

Cat in the stock dump is too restrictive?

Oh, you must be referring to this then :)

IMG_1804r.jpg

Yes Dunc. Change your sump pipe ASAP!

Either get in on the group buy unit or preferrably, talk to Scotty about one of his dump/front pipe units :happy:

Even if you don't touch the rest of your exhaust, change the dump pipe.

Certainly the biggest power boost when you do this. There is a massive cat in the middle of the stock dump that is soo restrictive.

+ 1 million! :happy:

I can vouch for the difference it makes even with a standard exhaust. Spools up faster, accelerates harder, more responsive, nicer engine note, slightly better fuel economy, need any more reasons? :)

20740_1304577929590_1084756809_30950462_4904169_n.jpg

  • 20740_1304576209547_1084756809_30950459_2070815_n.jpg
  • Splitfire Coil Packs
  • FMIC 11psi
  • SAFC II
  • 2.5" Gutted Cat

20740_1304576249548_1084756809_30950460_1467023_n.jpg

  • Same as above plus
  • 3" Front Dump pipe
  • SITC
  • 3, 1/4" Cat back
  • Reinforced intake pipe
  • Boxed pod with CAI
  • Grounding kit

20740_1304576289549_1084756809_30950461_5230306_n.jpg

  • Same as above plus
  • 3" Highflow cat
  • MV Auto's stage 2 shift kit

62434_1563571804275_1084756809_31610826_2250501_n.jpg

  • Same as above plus
  • R32 GTR 5 Speed, HD fly wheel and clutch
  • Denso Hi-flow fuel pump (stocker wasnt keeping up while being tuned today)
  • 12psi allthough it has to be pulled out towards the top so it doesnt hit boost cut :-(

Not sure where to from here.... Im at the end of the road AFM and turbo, tapping boost cut every so often.

post-40162-1285145722_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...