Jump to content
SAU Community

Recommended Posts

Works good too, brings it all on heaps earlier, just like the grub screw in the BOV. :thumbsup:

I just got back from tuning after fitting the stock turbo, it was only a temporary tune as Garrett is out of GTX turbo's at the moment. Running ethanol and pushing 1.2 bar the stocker made 225awkw and 850nm. I might just stick with this one for a while... :cheers:

This is a good representation of what a stock turbo (17psi) and a stage 2 (20psi) can do on ethanol, overlaid on the same graph. Cihan was very impressed with the stockers capabilities.

That's very impressive. How long would you expect the stock turbo to last at those pressures? So much has been written about short life expectancy if over 14psi. Is this temporary return to stock a bit of an experiment where you don't care if it lets go Scotty?

I would prefer if it didn't, and I only raised it 2 or 3 psi, should be ok.

I have an opinion on the failures, it seems to be the rear bearing that goes, possibly caused by oil starvation. The oil restrictor banjo bolt only has a 1mm hole and could easily block, especially if the engine internals are dirty. As mine has been flushed, I am hoping it will last just fine. It doesnt sound noisy like they usually do.

It could be a good idea to flush your engines and then check the hole isn't blocked...

I'm not tuning, I'm fabricating a stand for the extraction fan I gave him, the 1m blades should do the job nicely. I wont say what it will suck like... :)

Do you want me to make another modified actuator?

I would prefer if it didn't, and I only raised it 2 or 3 psi, should be ok.

I have an opinion on the failures, it seems to be the rear bearing that goes, possibly caused by oil starvation. The oil restrictor banjo bolt only has a 1mm hole and could easily block, especially if the engine internals are dirty. As mine has been flushed, I am hoping it will last just fine. It doesnt sound noisy like they usually do.

It could be a good idea to flush your engines and then check the hole isn't blocked...

I'd love to know where exactly this is so i could check. Is it on the block or turbo? Is it recommended to drill the hole out to (say) 1.5mm or does that cause other problems?

I'm very keen to make the std turbo last as long as possible and, given your results, it doesn't look like I need to put up with low power. Not saying I will run boost that high though.

It only made 2kw more with the higher boost, but 100nm extra torque.

The restrictor banjo is in the block, you can just get to it with a (17mm?) spanner. Don't strip the thread putting it back in... I dont know if drilling it out will be too much for the seals, probably not, perhaps you should just check it to make sure it is clear.

I think Scott's been drilling the hole to 3mm

Mmmm, 300% increase. Sounds like Scott :thumbsup:

Thanks Scott. You posted at same time. I will check that it is clear in the first instance. Maybe discuss improvements later...

Edited by Commsman

He'll have to answer that one LOL. Banjo bolt...somewhere on the turbo..?.:/

or not...:blush:

For some reason the song "The devil went down to Georgia" springs to mind. But I digress.

Works good too, brings it all on heaps earlier, just like the grub screw in the BOV. :thumbsup:

I just got back from tuning after fitting the stock turbo, it was only a temporary tune as Garrett is out of GTX turbo's at the moment. Running ethanol and pushing 1.2 bar the stocker made 225awkw and 850nm. I might just stick with this one for a while... :cheers:

This is a good representation of what a stock turbo (17psi) and a stage 2 (20psi) can do on ethanol, overlaid on the same graph. Cihan was very impressed with the stockers capabilities.

scotty,

Nice result with stock turbo, didnt think they would like running at 17-20psi, are they ceramic wheel?

Also your dyno graph doesnt have the power dipo at 3500rpm??? Do you run stock converter/trans?

Yep, ceramic but much different design to the Skyline/C34 wheel, ours run at 1 bar stock where theirs blow at over 12psi apparently. That is where the worry comes from I think as not too many of us have been comfortable with ramping the boost on the stocker.

Nope, My transmission has had a full build, still a work in progress. The 4000 stall dominator made me is a little too open, the factory lockup clutch you see in the dyno graph wont work and just slips as it is trying to haul in 1.5 - 2k revs (which it just cant do). I have disconnected the clutch for street and installed a 12v switch direct to the solenoid for dyno runs. It holds well over 1100nm of torque that way, I had it slipping at 24psi on my old turbo so im not sure where it will crap out with the Garrett GTX.

I am trying to source a spare torque converter to cut open, they are hoping to find as direct a replacement as they can to allow a larger clutch and more efficient stall stator to be fitted. Perhaps the Patrol TC may fit? Let me know if theres a spare M35 one around as this will be an issue for anyone building their box eventually.

I just got back from tuning after fitting the stock turbo, it was only a temporary tune as Garrett is out of GTX turbo's at the moment. Running ethanol and pushing 1.2 bar the stocker made 225awkw and 850nm. I might just stick with this one for a while... :cheers:

This is a good representation of what a stock turbo (17psi) and a stage 2 (20psi) can do on ethanol, overlaid on the same graph. Cihan was very impressed with the stockers capabilities.

So much more power where you can use it on a day to day basis.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to it's full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so damn hot in there, that made it all the more easy to remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. I was standing there looking at the car and said 'f**k it'. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...