Jump to content
SAU Community

Recommended Posts

that pipe is busted, however the front shocks are fine. $80 for the pair.

Hand brake lever it still there, but the cable is no longer attached as i am selling the cables seperately and i assumed that the guy needed that cables, but i'm not fully sure yet. You can buy the lever, and re attach your own cable fairly easily, just drill out the caulking join and spot weld the new cable in. if i don't sell that cable, i can reattach it for you if you like.

Make me offers for the quarter glass.

I have a set of 5 floor mats, but the drivers isn't in the best nick.

Bonnet cable with interior lever are still in good condition.

  • Replies 168
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

turns out firend didnt end up wanting the seats.

anyhow im after the trim in the boot, prety much the whole left side running up to the back of the seat and half of the trim on the right side (the part that covers the suspension tower). if you still have this how much you want and could you get a pic of it.

also i need a stock air box, cannot remeber if you had a pod or not. if you got this a price would also be nice

thanks

Jason

i have to idea how to measure up the tail lights. since they are not exactly square.

I do still have the bonnet cable. its yours for $20 +post. Pics of the mats may take a while cos i don't have a digicam.

the sunload sensor is still on the dash.

Linxus40 will have a PM

the lower dash surround, ie the one with the inserts used for switches has been sold along with the upper surround. If this is not what you were after please advise.

The dash pad is still available, however it has a bubble on the concave edge about between the pass and centre airvents. If you would still like pics, they can be arranged, however this may not adhere to your A1 prerequisite.

i have to idea how to measure up the tail lights. since they are not exactly square.

I do still have the bonnet cable. its yours for $20 +post. Pics of the mats may take a while cos i don't have a digicam.

the sunload sensor is still on the dash.

Linxus40 will have a PM

the lower dash surround, ie the one with the inserts used for switches has been sold along with the upper surround. If this is not what you were after please advise.

The dash pad is still available, however it has a bubble on the concave edge about between the pass and centre airvents. If you would still like pics, they can be arranged, however this may not adhere to your A1 prerequisite.

Yeh that was it :< Thanks anyway! If anyone else has one please PM me

  • 3 weeks later...

Hey chef, do u still happen to have the passenger front adjustable air vent by any chance? mine fell out today :D

Can you also email me with payment arrangements for the bonnet cable and interior lever please...my email it [email protected]

thanks heaps

Hey Chef,

Do u have the carpet that covers the spare tyre in the boot?

and also the centre air vents on dashboard?

and bonnet cable with interior lever?

Regards Joe

0402085323

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...